Determine the value of gravity in units of meters

Assignment Help Civil Engineering
Reference no: EM13211048

if a ball is dropped from a height of 800 cemtimeters, and the impact velocity is 41 feet per second, determine the value of gravity in units of meters per second.

Reference no: EM13211048

Questions Cloud

Find the final speed : Two carts with masses of 4.72 kg and 2.84 kg move toward each other on a frictionless track with speeds of 4.86 m/s and 3.97 m/s respectively. The carts stick together after colliding head-on. Find the final speed.
What is the force between the bar and block d : Block D sits freely on the homogeneous bar and experiences a gravitational force of 50N. Homogeneous bar AB experiences a gravitational force of 25 N. What is the force between the bar and block D?
Compute a satisfactory curve length : Assess the adequacy of this existing curve in light of the reconstruction design speed of 60 mi/h and, if the existing curve is inadequate, compute a satisfactory curve length.
Determine the height h : Determine the height "h" on the wall to which the firefighter can project water from the hose...and the speed of the water at the nozzle is v= 55ft/s. The firefighter is holding the hose 3.5 ft from the ground and the wall is located 15ft from the..
Determine the value of gravity in units of meters : if a ball is dropped from a height of 800 cemtimeters, and the impact velocity is 41 feet per second, determine the value of gravity in units of meters per second.
Calculate the expected shareholder value : Calculate the expected shareholder value generated by the business over the four years and indicate the effect of entering the new market on shareholder value.
Develop the relation between bulk unit weight : develop the relation between bulk unit weight, specific gravity, void ratio and weight of water.
How many kilograms each of pearlite : how many kilograms each of pearlite and preutectoid phase form? schematically sketch and label the resulting microstructure
What is the level of the service : If the peak-hour factor is .90 and all of the drivers are regular users, what is the level of the service of this compound-grade freeway segment?

Reviews

Write a Review

Civil Engineering Questions & Answers

  What are the tensions in cables ab and ad

The 20-kg mass is suspended from three cables. Cable AC is equipped with a turnbuckle so that its tension can be adjusted and a strain gauge that allows its tension to be measured. If the tension in cable AC is 40 N, what are the tensions in cable..

  Ratio of the magnitude in uniform electric field

What is the ratio of the magnitude of E2 to the magnitude of E1? You may neglect the effects of gravity on the proton.

  Investigate the possibility of environmental problems

Investigate the possibility of environmental problems that faced by the area of disaster.

  Determine the relevant pi groups

The break up of a liquid jet into droplets of diameter d depends on the jet diameter D, the jet velocity V, viscosity Mu, density rho,and surface tension sigma.

  Determination of edta titration

Does the presence of Mg2+ significantly interfere with the determination of Ca 2+ by the EDTA titration?

  Direction of flow in a conical tube

A conical tube of length 8 m fixed vertically with its smaller end upwards. The velocity head and pressure head at upper ends are 1.27 m and 2.50 m respectively.

  Supervisors technicians and skiled workers in dangerous work

As a project manager on site where work for 3 km long tunnel has been undertaken the site is remote and takes about 2 days to travel to nearest town supervisors technicians and skiled workers in dangerous work.

  Vehicle delay due to queuing

Vehicles begin to arrive at a toll booth at 850 am with an arrival rate of x(t) = 4.1 + .01t (with t in min and x(t) in veh /min.) The toll booth opens at 9am and processes vehicles at a rate of 12 per minute throughout the day. Assuming D/D/1 que..

  Maximum acceptable tensile service load

Compute the maximum acceptable tensile service load T that may act on a single angle L6x4x3/4 that is welded along only one leg to a gusset plate; thus, there are no holes. The service load is three times the dead load. Solve for a0 A36 steel.

  What are the factors affecting the hydraulic conductivity

what are the factors affecting the hydraulic conductivity?

  Overall gear reduction ratio

If the overall gear reduction ratio is 8 to 1, what is the maximum acceleration from rest (in ft/sec^2) for: a) the car with the base engine? b) car with the modified engine? Assume the car is on good dry pavement.

  Determine the value of po

determine the value of Po, as a funciton of H, for these two investment alternatives to be equivalent at an interest rate of i=15% per year.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd