Determine the unstretched length of spring

Assignment Help Civil Engineering
Reference no: EM13211096

Determine the unstretched length of spring AC if a force P = 110 lb causes the angle theta = 60^circ for equilibrium. Cord AB is 2 {rm ft} long. Take k = 50;{rm lb/ft}

Reference no: EM13211096

Questions Cloud

Find out the density of potassium in gcm3 : The radius of a potassium atom is 235 pm. Determine the density of potassium in g/cm3.
What is the spring constant : suppose you apply a force of 14.4 N to a spring and it stretches 2.4 cm. what is the spring constant?
Plot the magnitude of the force exerted on the gate : Plot the magnitude of the force exerted on the gate by the brace as a function of the angle of the gate, , for . Assume the weight of the gate is negligible.
Compute the partial pressure of each gas : Calculate the partial pressure of each gas and the total pressure if the temperature of the gas is 17?C.
Determine the unstretched length of spring : Determine the unstretched length of spring AC if a force P = 110 lb causes the angle theta = 60^circ for equilibrium. Cord AB is 2 {rm ft} long. Take k = 50;{rm lb/ft}
Determine the distance the engine is hoisted : The 3.5-Mg engine is suspended from a spreader beam having a negligible mass and is hoisted by a crane which exerts a force of 40 kN on the hoisting cable. Determine the distance the engine is hoisted in 2.4 s, starting from rest.
State the half-lives of different radioisotopes : The half-lives of different radioisotopes are given in the table below. If the initial amount of indium-117 is 8.4 g, how much indium-117 is left in the body after 86 minutes?
Improve financial literacy in canada : What the task force found and your opinion on their findings and different ideas you think could improve financial literacy in Canada
Explain in detail different types of surveys : what are the main points which create necessity of new railway line? explain in detail different types of surveys conducted in railway work.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Describe the use of productivity models for estimating land

Describe the use of productivity models for estimating land productivity. Provide details about various attributes that can be used and how the model is developed . Examples can be used to demonstrate model workability.

  Maximum total load that can be applied to a truss

How do you find the force ratio equation to determine the maximum total load that can be applied to a truss? Given a force of a member how do you find the force ratio?

  Find the rate of change in volume

A water tank has a height of 120m, and its area of cross-section is 2000m. Water is released from the tank and the water level drops by 1 meter every minute. Find the rate of change in volume.

  What the meaning of steady state

could you please help me to figure out what the meaning of steady state in the pavement management system preservation and rehabilitation.

  Total vehicle delay in the cycle with queueing diagram

If the queue clears exactly at the end of the effective green D/D/1 queuing applies, determine the total vehicle delay in the cycle (in veh-sec) .

  What is the elevation of lower point

A pre- engineering base line was run down a very steep hill.rather than measure horizontaily down hill with steel tape: surveyor measured the vertical angle with the theodolite and slope distance with 16m steel tape.

  Find the force that these gas generates on the top

the circular top of a can has a radius of .0320m. the pull-tab has an area of 3.8x10^-4 m^2. the absolute pressure of the carbon dioxide in the can is 1.40x10^5Pa. find the force that these gas generates on the top of a can?

  Purpose of the international space station

Briefly explain the purpose of the International Space Station, and list the name of all space agencies involved in building and operating it.

  What is the rate of evapouration of water

what is the rate of evapouration of water from a reservoir with air temp at 20c and the surface of reservoir is 3000m2.

  Strength of a semicrystalline polymer

Briefly explain how each of the following influences the tensile or yield strength of a semicrystalline polymer and why: (a) Molecular weight (b) Degree of crystallinity (c) Deformation by drawing (d) Annealing of an undeformed material

  Deflection of a simple uniformly loaded beam

Determine the deflection of a simple uniformly loaded beam by the Ritz method,using first one term, then two terms, adn finally three terms in a sine series. Why does the coefficient of sin2piex/L vanish?

  Mass of water vapor diffuses through tube

If the water vapor is removed from the upper tank so that the concentration there remains nearly zero, what mass of water vapor diffuses through the tube each hour?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd