Determine the tension in cable bo immediately

Assignment Help Mechanical Engineering
Reference no: EM131122795

Problem 1 -

Given: An inhomogeneous disk (having a mass of m, outer radius R, mass center at G and centroidal radius of gyration of kG) moves along a SMOOTH horizontal surface. The distance from the geometric center O of the disk to the center of mass G is given by e. At the instant shown, G is at the same vertical height as O as the disk translates to the right with a speed of vO.

Determine the normal force of the ground acting at the contact point C at this instant.

812_Figure.png

Use the following parameters in your analysis: m = 10 kg, R = 0.5 m, e = 0.3 m, kG = 0.4 m and vO = 20 m/s.

Problem 2 -

Given: The homogeneous thin bar AB shown below has a mass of M and a length of L. The bar is supported by lightweight, inextensible cable BO at end B and by a smooth, inclined wall at end A. The bar is released from rest with the bar in a horizontal orientation and with cable BO being vertical.

Determine the tension in cable BO immediately after the bar is released.

2373_Figure1.png

Use the following parameters in your analysis: M = 100 kg, L = 3 m and θ = 53.13o.

Reference no: EM131122795

Questions Cloud

Describe a sensor that would give an electrical output : Feedback control requires being able to sense the variable being controlled. Because electrical signals can be transmitted, amplified, and processed easily, often we want to have a sensor whose output is a voltage or current proportional to the va..
What maximum internal pressure can be applied : If the maximum hoop stress permitted on the inside wall of the cylinder is limited to 30 MN/m2, what maximum internal pressure can be applied assuming the cylinder has closed ends
Describe an actuator that could accept an electrical input : Feedback control requires being able to sense the variable being controlled. Because electrical signals can be transmitted, amplified, and processed easily, often we want to have a sensor whose output is a voltage or current proportional to the va..
Review membership requirements and member benefits : Review membership requirements and member benefits and compare your interests and what you want from a networking organization to the benefits and mission statement offered by the organizations you identify (Costello, 2012).
Determine the tension in cable bo immediately : The homogeneous thin bar AB shown below has a mass of M and a length of L. The bar is supported by lightweight, inextensible cable BO at end B and by a smooth, inclined wall at end A. Determine the tension in cable BO immediately after the bar is r..
Journalize the entries to record the transactions : The following selected transactions were completed by Artic Company during February of the current year. Artic Company uses the periodic inventory system.
What is the meaning of collocated control : what is the meaning of "collocated control"? "Noncollocated control"?
Complete the following table by indicating : Complete the following table by indicating for (a) through (g) whether the proper answer is debit or credit.
Describe the history of public administration : Write a 500 to 700 word paper in which you describe the history of public administration. Include a description of at least two public administration models.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd