Determine the tension in cable ac

Assignment Help Mechanical Engineering
Reference no: EM13704532

The boom OA carries a load P and is supported by two cables as shown. Knowing that the tension in cable AB is 183 lb and that the resultant of the load P and of the forces exerted at A by the two cables must be directed along OA, determine the tension in cable AC.

Reference no: EM13704532

Questions Cloud

Meteorologist uses pitot-static tube to measure wind speed : A meteorologist uses a pitot -static tube to measure the wind speed in a tornado. Based on the damage caused by the storm, the tornado is rated as EF5 on the enhanced Fujita Scale. This means that the wind speed is estimated to be in the range of 261..
What is the maximum rated engine speed : You are designing a 4-stroke cycle diesel engine to provide a brake power of 300 kW naturally aspirated at its maximum rated speed. Based on typical values for BMEP and mean piston speed, estimate the required engine displacement, and the bore and st..
Diameter alloy rod has elongated-diameter has been reduced : At the proportional limit, a 1.5-in. gage length of a 0.375-in.-diameter alloy rod has elongated 0.0081 in. and the diameter has been reduced 0.00071 in. The total tension force on the rod was 5.62 kips.
A hypothetical metal has hcp crystal structure with ideal : A hypothetical metal has an HCP crystal structure with the ideal c/a ratio (1.633). What is the volume of its unit cell, if the atomic radius is 1.3A?
Determine the tension in cable ac : The boom OA carries a load P and is supported by two cables as shown. Knowing that the tension in cable AB is 183 lb and that the resultant of the load P and of the forces exerted at A by the two cables must be directed along OA, determine the tensio..
Calculate the work done by the steam during this process : Five kilogram of saturated water vapor at 300 kPa is heated at constant pressure until its temperature reaches 200oC. Calculate the work done by the steam during this process.
Determine the value of the polar coordinates of the point : A particle moves along a spiral described by the equation r=r(inital)+kappa*theta, where r(inital) and kappa are constants, and where theta is in radians. Assume that theta dot =alpha*time, where alpha= 0.15rad/s^2 and t is time expressed in seconds.
Cold cranking amperes of a conventional lead-acid : The cold cranking amperes (CCA) of a conventional lead-acid automobile battery is the amount of current the battery can provide at 0°F for 30 seconds and minute in at least 1.2 volts per cell (or 7.2 volts for a standard 12-volt battery). If a batter..
Aircraft executes horizontal turn at constant true air speed : In a correctly banked turn of radius R, an aircraft executes a horizontal turn at constant true air speed, V, with no sideslip and zero roll rates. The aircraft must bank at an angle phi from the horizontal so that the horizontal component of its lif..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Heat transfer coefficient at the surface of the base plate

Consider a 1000-W iron whose base plate is made of .5 cm thick aluminium alloy 2024-T6 (p = 2270 kg/m^3, cp= 875 J/kg*K, alpha = 7.3 x 10 ^-5 m^2/s). The base plate has a surface area of .03 m^2.

  A minimum stress of -20 mpa compressive stress if a fatigue

for a specimen under fatigue test with a maximum stress of 150 mpa tensile stress and a minimum stress of -20 mpa

  Five kilograms of water h2o sealed in a piston-cylinder

five kilograms of water h2o sealed in a piston-cylinder device undergoes 3 quasi-equilibrium processes that complete a

  Calculate the ratio of the exit flow area to the inlet flow

air enters an insulated diffuser operating at steady state with a pressure of 105 nm2 and a temperature of 57 degrees

  A balanced wheel supported on springs is rotating at 1200

a balanced wheel supported on springs is rotating at 1200 rpm. if a bolt weighing 15 g and located 5 cm from center

  What is the pressure in the tank

If 300 Kg of air is pumped into a previously empty 100 m^3 tank, and the temperature of the air in the tank is 25 deg C, then what is the pressure in the tank in N/m^2?

  In order to measure the volume flow rate of fresh water

q1.a single stage reciprocating compressor has a swept volume of 0.4 litres and operates at 1440 rpm through a pressure

  The final temperature

1. Water vapour at 90kPa and 150°C enters a subsonic diffuser with a velocity of 150m/s and leaves the diffuser at 190kPa with a velocity of 55m/s and during the process 1.5 kJ/kg of heat is lost to surroundings. Determine (i) The final temperature (..

  Methane ch4 at 25 c 1 bar enters a furnace operating at

methane ch4 at 25 c 1 bar enters a furnace operating at steady state and burns completely with 140 of theoretical air

  Determine the hertz contact stresses for a 50 n coupling

a 2-2-2 kinematic coupling uses 19-mm silicon nitride balls and tungsten carbide vees. determine the hertz contact

  Pressure ratio 92 air at compressor inlet is at 25 deg f

consider a brayton cycle with the following given data pressure ratio 9.2 air at compressor inlet is at 25 deg f air

  Assume the tank is well-insulated determine the temperature

a scuba divers 2 ft3 air tank is to be filled with air from a compressed air line at 120 psia and 100 degree f.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd