Determine the required sampling rate and the data rate

Assignment Help Electrical Engineering
Reference no: EM13247091

An ultrasound image analog signal needs to be converted to a digital bit stream. The bandwidth of the signal is from 500 kHz to 2.0MHz, and the necessary resolution is 12 bits. determine the required sampling rate and the data rate (bits/second of the resulting bit stream

Reference no: EM13247091

Questions Cloud

What is the probability of three successes : What is the probability that a randomly selected person will be a Protestant and at the sametime be a Democrat or a Republican and what proportion of teenagers watch 16 to 18 hours of TV a week?
Calculate both doping densities in silicon junction : A silicon (ni= 10^10 cm^-3) p-n junction diode has a maximum electric field of -10^6 V/cm and a depletion layer width of 1 um. The acceptor density in the p-type region is four times larger than the donor density in the n-type region.
Determine the wavelength of the light : The beam from a diode laser is used to investigate the refraction of a piece of plastic. Determine the wavelength of the light in the plastic in nanometers (nm).
How far is lenny from the keys : Carl and Lenny are trying to find Carl's keys that are beeping-he attached a device to beep when you whistle for this purpose, how far is Lenny from the key's
Determine the required sampling rate and the data rate : An ultrasound image analog signal needs to be converted to a digital bit stream. The bandwidth of the signal is from 500 kHz to 2.0MHz, and the necessary resolution is 12 bits. determine the required sampling rate and the data rate
Explain solution was then titrated to a blue-black endpoint : The solution was then titrated to a blue-black endpoint with 26.0mL of a 0.0163 M KIO3 solution. How many mg of Vitamin C were in the tablet ?? and what % of the powder was Vitamin C?? Please solve this out for me
Calculate the radius of an oil drop : In the Millikan oil-drop experiment illustrated in the figure below, an atomizer is used to introduce many tiny droplets of oil between two oppositely charged parallel metal plates, Estimate the radius of an oil drop of density 854 kg/m3 for which it..
Explain the zinc compartment causing precipitation : Consider the standard cell at 25C based on the following half-reactions. Pb^2+ + 2e^- --> Pb E=-0.13V Zn^2+ + 2e^- --> Zn E=-0.76V To the standard cell, OH-, is added to the zinc compartment causing precipitation of Zn(OH)2. After precipitation is..
Explain half cells compare electrode potentials calculated : For each of the half cells compare electrode potentials calculated from (1) concentration and (2) activity data. a) HCl (0.0200 M), Nacl (0.0300 M)|H2 (i.00 atm), Pt b) Fe(Clo4)2 (0.0111M), Fe(ClO4)3(0.0111M)|Pt

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the line impedance and line current

In a balanced three-phase wye-wye system, the load impedance is 10 +j1 Ohms. The source has phase sequence abc and the line voltage Vab = 220 Vrms /30°. The load voltage is VAN = 120 Vrms /0°.

  Write a matlab program to compute the capacity

Write a MATLAB program to compute the capacity of an AWGNC with a given bandwidth and for equally spaced values of between and including and (in dB).

  Write a program that reads a nonnegative integer

The factorial of a nonnegative integer n is written n! (pronounced "n factorial") and is defined as follows: n!= n(n-1)(n-2)(n-3)....1 (for values of n greater than or equal to 1) and n!= 1 (for n=0) for example 5! = 5x4x3x2x1,

  What is voltage present after ten second delay

In a power supply, a 150 microfarad capacitor was connected in parallel with a 200 kOhm resistor. The capacitor was maintained at a charge level of 350 volts DC. After power was removed for ten seconds, someone god a shock from touching the termin..

  How much energy is required to increase diameter of water

1- If the diameter of a spherical water droplet is 100.0 µm, how much energy is required to increase the diameter of the water droplet by 3.0 µm The surface tension of water is 1.0 x 10-3 J/m2. 2- A metal crystallizes in a face-centered cubic lat..

  What is the magnitude of the impedance at an frequency

A parallel-resonant RLC circuit has R = 75 I, L=50mh, and C=45pF. A) Sketch and label the circuit. B) Find fo, the resonant frequency. C) At what frequency is impedance a maximum D) What is the magnitude of the impedance at this frequency

  Determine the energy in the signals odd part

A signal x(t) can be represented as x(t)=xe(t)+xo(t) where xe(t)=(1/2){x(t)+x(-t)} is the even part, and xo(t)=(1/2){x(t)-x(-t)} is the odd part of the signal. Let x(t) be an energy signal with an energy of 20 Joules. Suppose the even part of x(t) is..

  How to compare the values of h and m obtained

A "ferrite" having a relative permeability of 50 H / m, that operates with flux densities sufficiently small, may be considered a single material. If the magnetic flux density in the material is B = 0.05 T, H and M. halle How to compare the values

  Determine how much is the separation between the plates

In one type of computer keyboard, each key holds a small metal plate that serves as one plate of a parallel-plate, air-filled capacitor. When the key is depressed, the plate separation decreases and the capacitance increases.

  Explain which parameter of an fm transmission determines

Do either or both of the reasons you gave in part (a) above also apply to a point to point voice link using frequency modulation? c. Which parameter of an FM transmission determines whether it is wideband or narrow band?

  Generate a clock signal with 5 khz frequency

Write an asm HCS12 program to flash LEDs on a dragon+ board three times when SW5 is pressed with a 5 kHz frequency, and 50% duty cycle clock signal. Generate a clock signal with 5 kHz frequency, and 50% duty cycle.

  Obtain the impulse responses of the systems

(a) The ideal delay system. y[n] = x[n-nd] (b) The accumulator system. y[n] = sum (xk) , k from -inf to n (c) Forward difference system. y[n] = x[n + 1]- x[n] (d) Backward difference system. y[n] = x[n]- x[n - 1]

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd