Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Given the following information, determine the required DO concentration in the treatment plant effluent discharge in order to ensure that at no point downstream the DO in the river drops below 4 mg/L:
QR = 16 m3/s
QW = 4 m3/s
T = 12°C
kd = 0.2 d-1
kr = 0.6 d-1
DOR = 8 mg/L
BODW = 50 mg/L
BODR = 5 mg/L
The coefficient ofrestitution between each car is 0.8 . Determine the final velocityof each car, after all impacts, assuming (a) cars A and C hit Car Bat the same time, (b) car A hits car B before car C does.
The top and bottom pull to the left with 10 kips each, the middle part 20 kips to the right. The bolts have a diameter 3/8 inch, determine the average shear stress on the bolt surfaces that are subjected to direct shear.
Prove that the smallest angle of any triangulation of a convex polygon whose vertices lie on a circle is the same. This implies that any completion of the Delaunay triangulation of a set of points maximizes the minimum angle.
Suppose that a person who boards the elevator on the ground floor gets off on the fifth floor. Assuming that the elevator has achieved operating speed by the time it reaches the second floor and that it is still moving at its operating speed as it..
A U manometer reads 20 cm air as operating fluid and a given manometric fluid. A single branch closed tube reads 35 cm connected to point 1. If P2 = 1.2 ATM calculate the pressure in point 1 and the density of the manometric fluid.
Determine the torque that the Titanium Alloy shaft can transmit if the allowable angle of twist is 0.375 RAD. Assume the torque is applied at the end of the shaft. The shaft is 2 meters long and has a diameter of 25 mm.
A column of dimensions 200 X 300 mm has an effective length of 3m. It is reinforced with 6 HYSD bars of 20mm diameter. Determine the safe load the column can carry using working method of design. Using M20 Concrete.
During a 1.5-hr storm, 1.3 in. of rain fell during the first hour, and 0.4 in. of rain fell during the last half hour. The average flow in the downspouts was 1.7, 3.6, and 3.4 ft3/sec for each of the half-hour periods.
The discharge of the river at the basin outlet is measured at an avarage of 650 cfs. assuming that the charge in storage for the system is essentially zero, estimate the ET losses for the area in inches and centimeters for the year
The acceleration of a particle as it moves along a straight line isgiven by a = (2t-1)m/s2 where t is in seconds. If s =1mand v =2m/s when t =0 determine the particles velocity and positionwhen t = 6s. Also determine the total distance the particle t..
Suppose that in an apparatus it is necessary to maintain precisely the cross section of a 20mm circular nickel steel bar. If this bar is heated to 200 deg Celcius, what tensile force should be applied to the bar to maintain its cross sectional dim..
The inlet of loe pressure turbine is 500Kpa and 500°C. Condenser operates at 10 Kpa. Determine the mass flowrate through boiler needed to produce 5000KW of power.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd