Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
The shaft in Figure P12-3 is part of a special machine designed to reclaim scrap aluminum cans. The gear at B delivers 5 hp to a chopper that cuts the cans into small pieces. The V-belt sheave at D delivers 3 hp to a blower that draws air through the chopper V-belt sheave E delivers 3 hp to a conveyor that raises the shredded aluminum to an elevated hopper The shaft rotates at 480 rpm. All power comes into the shaft through the chain sprocket at C. Use AISI 1137 OQT 1300 steel for the shaft. The elements at B, C, D. and E are held in position with retaining rings and keys in profile keyseats. The shaft is to be of uniform diameter, except at its ends, where the bearings are to be mounted. Determine the required diameter
Water boils at room temperature of 25 degrees celsius when the pressure is 3.17 kPa (abs). Express this as a vaccum gage pressure (in mmHg) if atmospheric pressure is 101 kPa. Provide details of work to get a good rating.
A turbine located 225 m below the water surface at intake, carries a flow of 3.5 m^3/s. The head loss in the pipeline leading to it is 10 m. Find the power (kW) delivered by the turbine if its efficiency is 92%.
If a sample for BOD needs to be diluted by a factor of 0.02 , calculate the volume of sample that will be used in the BOD bottle
A 0.20 kg stone attached to a 0.8 m long string is rotated in a horizontal plane. The string makes an angle of 25° with the horizontal. Determine the speed of the stone.
Consider an air bubble rising from the bottom of a lake. Neglecting surface tension, determine approximately what the ratio of the density of the air in the bubble will be at a depth of 34ft to its density at a depth of 8 ft
two 10 mm thick steel plates are fastened together by means of two 20mm bolts that fit tightly into the holes. if the joint transmits a tensile force of 45 kn determine the average normal stress in the plates at a section where no holes occur
A wood mallet has a cylindrical head 6 inches long and 3 inches in diameter. If the cylindrical head is 1 inch in diameter how long must it be for the mallet to balance at a point 6 inches from where the handle enters the mallet? (use 40 lb / ft cube..
Refrigerant 22 is used in the evaporator pipe of a commercial refrigeration unit. At steady state it flows at a rate of 0.5 kg/s through the pipe of constant diameter. It enters the pipe at -10C with a velocity of 5 m/s and a quality of 25%.
Could all the people in china hold back the water behind the three gorges dam?
A solid ball starts to roll up a hill with an initial velocity of 50m/s. The ball has a mass of 20 Kg with a 0.75 m radius. How high did the ball roll before it momentarily stopped
An automobile having a mass of 900 kg initially moves along a level highway at 100 km/hr relative to the highway. It then climbs a hill whose crest is 50m above the level highway and parks at a rest area located there
in an air standard otto cycle , the air at the beginning of the compression stroke is at 95 kpa and 22c ,and the cylinder volume is 0.0028 m^3 . the compression ratio is 9 and 4.3 kj are added during the heat addition process
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd