Determine the radius of curvature of the particle path

Assignment Help Mechanical Engineering
Reference no: EM13710340

A particle which movies in a two-dimensional curvilinear motion has coordinates in millimetres which vary with time t in seconds according to x=5t2 +4 and y=2t3 + 6. For time t =3s, determine the radius of curvature of the particle path and the magnitudes of the normal and tangential accelerations.

Reference no: EM13710340

Questions Cloud

Hot water is provided to a house by electric water heater : Hot water is provided to a house by an electric water heater which uses a 60L tank. The electric heater is rated for a 1.6kW. The hot water tank is completely full with water at 80°C when someone starts a shower. The shower faucet mixes cold water at..
What is the annual after-tax cost of debt : What is the annual after-tax cost of debt to the company on this issue and how much must the assets be reduced to bring the TATO to the industry average - what is the project's IRR?
What is final temperature and assume process is adiabatic : An evacuated 1-ft3 tank is connected by a valve to a nitrogen supply line flowing air at 120 psi and70oF. A valve is opened allowing air to flow into the tank until the pressure reaches 90 psi. How much mass flowed into the tank and what is its final..
Consider the variation of specific heat with temperature : A gas turbine power plant operating on an ideal Brayton cycle has a pressure ratio of 7. Determine the back work ratio of this cycle, if the temperature of air at the compressor and the turbine inlet are 300 K and 1300 K respectively. (Consider the v..
Determine the radius of curvature of the particle path : A particle which movies in a two-dimensional curvilinear motion has coordinates in millimetres which vary with time t in seconds according to x=5t2 +4 and y=2t3 + 6. For time t =3s, determine the radius of curvature of the particle path and the magni..
Neglect kinetic-potential energy changes-compressor power : Air is compressed at steady state from 100 kPa, 300 K, to 600 kPa, 440 K with a mass flow rate of 4 kg/s. Heat transfer occurs at a rate of 42.3 kJ/kg of air flowing to cooling water circulating in a water jacket enclosing the compressor.
What is the mass flow rate of gaseous oxygen : Liquid oxygen (LOX) is used as rocket fuel to launch satellites into space. However, it is easier (and less dangerous) to transport oxygen in gaseous form. What is the mass flow rate of gaseous oxygen that flows at 25 m/s through a 0.5-meter diameter..
Neglecting heat transfer and potential energy : Steam enters a nozzle at steady state at 20 bar and 280°C, with a velocity of 80 m/s. The exit pressure and temperature are 7 bar and 180°C. Mass flow rate is 1.5 kg/s. Neglecting heat transfer and potential energy. Sketch the process on a T-v diagra..
Calculate product temperature at the center : A cooked mashed potato is cooled on trays in a chilling unit with refrigerated air at 2 C blown over the product surface at high velocity. The depth pf the product is 30mm and the initial temperature is 95 C. The product has a thermal conductivity of..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Calculate the load capacity of a precast concrete pile

Calculate the load capacity of a precast concrete pile that is 14in. in diameter and is driven into soil resistance of 2.5 tons per square foot. Assume the top 5 feet of the pile cannot develop any shear resistance. Total pile length is 35 feet.

  Calculate the density in gramcm3 of a perfect aluminum

aluminum atoms have a radius of 0.1431 nm and they form into face-centered cubic fcc crystals.a calculate the density

  Determine the final absolute pressure kpa of the gas

the pressure of a gas inside a piston-cylinder device is initially balanced by an atmospheric pressure of 100kpa and an

  A 90kw ideal power cycle takes in air at pressure 90kpa

a 90kw ideal power cycle takes in air at pressure 90kpa and discharges it at 945kpa. determine the rate of heat input

  Heat is added to the water at a rate of 500 w how long

a pot containing 1.0 liters of water at 20 degc is placed on the stove and heat is added to the water at a rate of 500

  A 0500-kg particle has a speed of 250 ms at point circle a

a 0.500-kg particle has a speed of 2.50 ms at point circle a and kinetic energy of 7.40 j at point circle b.a what is

  If the fluid is gasoline at 20 degrees celsius and the flow

a centrifugal pump has d1 6 inches d2 14 inches b1 5 inches b2 4 inches beta1 20 degrees beta2 45 degress and rotates

  Water exiting the condenser of a power plant at 38ordmc

water exiting the condenser of a power plant at 38ordmc enters a cooling tower with a mass flow rate of 4.5 x 107 kgh.

  Determine the work required to compress steam

determine the work required to compress steam isentropically from 100 kpa to 1 mpa assuming that the steam exists as a

  The material used in its construction can be considered

the eifel aqueduct was built in 80 ad to provide water to present-day city of cologne. as one of the longest aqueducts

  The speed of water at the beginning of the pipe is 150 fts

water flows into an 9.0 diameter section of a piping system then it exits from 3.0 x 4.0 rectangular section. the speed

  Estimate the heat transfer area of the heat exchanger

an ocean thermal energy conversion otec system is proposed to generate 10 mw of electricity. the proposed location of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd