Determine the position where the net electric field is zero

Assignment Help Civil Engineering
Reference no: EM13304064

Given that the seperation distance between the charges is 5m, q1 = -3q2, find the position where the net electric field is zero. Do not use infinity.

Reference no: EM13304064

Questions Cloud

Determine the ratio k of the tension in the remaining wire : The small sphere of mass (m) is suspended initially at rest by the two wires. If one wire is suddenly cut, determine the ratio (k) of the tension in the remaining wire immediately after the other wire is cut to the initial equilibrium tension.
Determine the components of the 800 lb force f along axes : determine the components of the 800 lb force f along the oblique axes a and b. also, determine the projections of f onto the a and b axes
What is concentration of fe needed to maintain concentration : At a wastewater treatment plant, FeCl3 (s) is added to remove excess phosphate from the effluent. Assume the following reactions occur: FeCl3(s) Fe3+ + 3Cl- Fe3+ + PO4 (3-) FePO4 The equilibrium constant for the second reaction is 10^26.4.
Internal and external environmental analysis : Conduct an internal and external environmental analysis for your proposed business. Discuss with your Learning Team the forces and trends below that must be taken into consideration while developing a strategic plan.
Determine the position where the net electric field is zero : Given that the seperation distance between the charges is 5m, q1 = -3q2, find the position where the net electric field is zero. Do not use infinity.
What is lowest grade possible for the constant-grade section : A tangent section of highway has a -1.0% grade and ends at station 0+1450and elevation 25m. It must be connected to another section of highway that has a -1% grade and that begins at station 1+345 and elevation 40m.
Space shuttle challenger launch in 1986 was a disaster : The Space Shuttle Challenger launch in 1986 was a disaster. Seven crewmen died and the shuttle program was put on hold. Using the search engine of your choice, do a search on this disaster and examine the decision-making process regarding the launch.
Determine mass of nitrogen using the ideal gas model : A tank contains 0.05 m^3 of nitrogen gas at -21 C and 10 MPa. Determine the mass of nitrogen, in kg, using: a) the ideal gas model b) data from the compressibility chart Comment on the applicability of using the ideal gas model for nitrogen at thi..
How much does the student have to pay at the end of 3 years : The compound interest formula is F=P(1+i)n where F is the total amount due, P is the initial cost or amount of money, i is the interest rate, and n is the number of periods interest is computed. 1.A student purchases a $1400 laptop computer for sc..

Reviews

Write a Review

Civil Engineering Questions & Answers

  What proportion of the true stress is the applied stress

A 10cm long cylindrical rod of steel is elongated to become 12.1cm long by the application of a force of 10kN. 1- What is the ration of initial diameter to final diameter, assuming no net volume change

  Calculating sand shear strength

Estimate the effective friction angle for the sand (assume c' = 0). Calculate the sand's shear strength (τf) on a horizontal plane at depths of the 20 ft and 50 ft.

  Velocity and acceleration of the flow

The volume flow rate of streams into the pipe is given by QA = 0.02t m 3 /s and that of stream B by QB = 0.008t 2 m 3 /s, where t is in seconds. The exit area of the pipe is 0.01m 2 . Find velocity and acceleration of the flow at exit at t = 1s.

  Compute the maximum acceptable tensile load

Compute the maximum acceptable tensile load Pu, on an angle L6x4x3/4 when connected to both legs. The 4 in. leg contains a single gage line of 7/8in. diameter bolts, and the 6in.

  Supporting Investment Promotion: ERNST & YOUNG

Ernst & young is currently providing support to various sectors. In this regards it was felt that if this report is able to document good practices currently being adopted or planned in ceramic sector.

  What is the engine speed in revolutions per minute

The air density is 0.00206 slugs/cuft. The car has frontal area of 19.8 sqft, a drag coefficient of 0.28, a wheel radius of 12.6 inches, a drive axle slippage of 3%, and a drivetrain efficiency of 88%.

  Shafts in a speed-reducer unit

The two shafts in a speed-reducer unit are subjected to couples of magnitude M1 = 18 N · m and M2 = 7.5 N · m, respectively.

  Find the gauge pressure at a second point in the line

At one point in a pipeline, the water's speed is 3.00 m/s and the gauge pressure is 4.00×10^4 Pa. Find the gauge pressure at a second point in the line 11.0 m lower than the first if the pipe diameter at the second point is twice that at the first..

  Design condition inflow and pumping rates

Derive an equation that allows you to compute the diameter of the drain hole for a desired steady water height in the tank for the design condition inflow and pumping rates.

  Conductive heat loss through the furnace wall

Assuming unit surface area, find the conductive heat loss through the furnace wall and the temperature at the interface of the fire clay and red brick.

  How much does the student have to pay at the end of 3 years

The compound interest formula is F=P(1+i)n where F is the total amount due, P is the initial cost or amount of money, i is the interest rate, and n is the number of periods interest is computed. 1.A student purchases a $1400 laptop computer for sc..

  Determine the magnitudes of the lift and drag

The forces acting on the sailplane are represented by three vectors. The lift L and drag D are perpendicular. The magnitude of the weight W is 500 lb. If the magnitude of the resultant of the three forces is 0

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd