Determine the pitching moment

Assignment Help Mechanical Engineering
Reference no: EM131366132

Thrust vector control is a technique that can be used to greatly improve the maneuverability of military fighter aircraft. It consists of using a set of vanes in the exit of a jet engine to deflect the exhaust gases as shown in Fig. P5.76.

(a) Determine the pitching moment (the moment tending to rotate the nose of the aircraft

1252_4647a733-adf4-4dd6-8eb5-2d82178eea67.png

up) about the aircraft's mass center (cg) for the conditions indicated in the figure.

(b) By how much is the thrust (force along the centerline of the aircraft) reduced for the case indicated compared to normal flight when the exhaust is parallel to the centerline?

Reference no: EM131366132

Questions Cloud

What is the first step in the formation of soil : 1. What is the first step in the formation of soil? 2. How is the soil texture that develops from decomposing sandstone likely to be different from soil that develops from shale?
Chemicals of life and cell structures : Instructions: Select one of the following discussion topics for your primary post, which should address the discussion question in at least 125 words. Also, please respond to a fellow student on any topic.
What special maneuvers will you perform : Consider the possible origins using the Agency for Healthcare Research and Quality (AHRQ) guidelines as a framework. What physical examination will you perform? What special maneuvers will you perform
Describe the cyclic activated-sludge system : Describe the Cyclic Activated-Sludge System, discuss its mode of operation and the potential benefits as an equipment option for an activated sludge unit to be designed into a batch wastewater pretreatment system. Your response should be at least ..
Determine the pitching moment : Thrust vector control is a technique that can be used to greatly improve the maneuverability of military fighter aircraft. It consists of using a set of vanes in the exit of a jet engine to deflect the exhaust gases as shown in Fig. P5.76.
What is global warming : What is global warming? Describe how human activities impact global warming. Explain what an individual can do to minimize his/her contribution to global warming.
Contribution of plastic to municipal solid waste stream : Here is the question: Discuss the contribution of plastic to the municipal solid waste stream and describe the four main categories of plastic and solid waste recycling techniques.
Identifying specific characteristics of effective managers : Post an analysis of how management and leadership roles differ in terms of supporting an organization to set and achieve goals. Provide your rationale, identifying specific characteristics of effective managers and leaders
Some biologists consider evolution to be a fact : Some biologists consider evolution to be a fact. In your opinion, is it really a fact? Why? Is there a valid debate about evolution? Support your response with evidence.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Ametal has a cubic structure with a density of 1892 gcm3

a metal has a cubic structure with a density of 1.892 gcm3 an atomic weight of 132.91 gmol and a lattice parameter of

  In such an experiment for which steady state operation is

the thermal characteristics of a small dormitory refriderator are determined by performing two separate experemints

  Floor space of any facility that houses shell

The floor space of any facility that houses shell-and- tube heat exchangers must be  sufficiently  large  so the tube bundle can be serviced easily. A rule of thumb is that the floor space must be at least 2.5 times the length of the tube bundle s..

  Composition of the equilibrium mixture

Methane burns with 90% of theoretical air to form an equilibrium mixture of CO2, CO, H2O(g), H2, and N2 at 1000 K, 1 atm. Determine the composition of the equilibrium mixture, per kmol of mixture.

  Determine the cycle thermal efficiency for the cycle when

an air standard brayton closed cycle receives air at 1 atm and 298 k. the upper temperature and pressure limits are 5

  Calculate the force necessary to cause

A cylindrical specimen of this alloy 24 mm in diameter and 186 mm long is to be pulled in tension. Calculate the force necessary to cause a 0.0119 mm reduction in diameter. Assume a value of 0.33 for Poisson's ratio.

  Determine a the initial acceleration of the projectile b

a projectile enters a resisting medium a x 0 with a initial velocity of vo 900 fts and travels 4 in. before coming to

  Assume both will be worthless after 6 years and that the

two workstations are being conciered by your company. machine 1 costs 12000 new and 1300 to operate and maintain each

  How much strain energy u is stored in the beam

A simply supported beam of length L is subjected to loads that produce a symmetric deflection curve with maximum deflection at the midpoint of the span.

  Resistance of the alloy to crack nucleation

Would you expect the fracture toughness of quenched and tempered aluminum bronze to be high or low? Would there be a di¤erence in the resistance of the alloy to crack nucleation compared with crack growth? Explain.

  How would you define a system to determine the temperature

a how would you define a system to determine the temperature rise created in a lake when a portion of its water is used

  When you move up from the surface of the earth the

when you move up from the surface of the earth the gravitation is reduced as g 9.807 - 3.32 times 10-6 z with z as the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd