Determine the phase margin of the amplifier

Assignment Help Electrical Engineering
Reference no: EM131226874

The open-loop amplifier of a feedback system has its first two poles at fP1 = 1 MHz and fP2 = 10 MHz, and has a low-frequency open-loop gain of |Ao| = 100 dB.

(a) A dominant pole is to be added such that the closed-loop amplifier with a low-frequency gain of 20 has a phase margin of 45 degrees. What is the dominant pole frequency?

(b) If the feedback transfer function from part (a) is increased such that the closed-loop low-frequency gain is 5, determine the phase margin of the amplifier.

Reference no: EM131226874

Questions Cloud

Determine the new dominant pole frequency : Determine the new dominant pole frequency  and phase margin if the compensation capacitor is increased to CF = 75 pF.
Design a direct-coupled inverting op amp with a gain : Design a direct-coupled inverting op amp with a gain of -100 VN, the highest possible input resistance, and an output offset 50.5 V. using an op amp with 2 mV offset, and bias currents of 1 pA equal to within ±10%. What is Ra, of your design?
Evaluate difference between different type of payment method : Analyze the market forces that would favor using one reimbursement method over another. Evaluate the key differences between different types of payment methodologies from the provider and hospital point of view.
What do you estimate the input offset voltage to be : Now, if the 10 kΩ resistor connected to the amplifier's negative input terminal is capacitor-coupled to ground, what does the output offset voltage become? What must you now do to compensate? What does the output offset voltage now become?
Determine the phase margin of the amplifier : The open-loop amplifier of a feedback system has its first two poles- What is the dominant pole frequency?  -Determine the phase margin of the amplifier.
Brief response to these potential objections : As a community member, submit a one-paragraph article that details your reasonable objections to the proposed project. As a student, follow up with a brief response to these potential objections.
What are its peak and average and values : what are its peak and average and values ? what do the peak and average diode current become whem vb reaches 14 v ?
Analyze the intended strategy of your firm as described : In section 2, you will analyze the intended strategy of your firm as described in annual report/website. How well has company executed this strategy?
Mortgage according to the loan agreement : You borrow $245,000 to buy a house. The mortgage rate is 4.5 percent and the loan period is 30 years. Payments are made monthly. If you pay the mortgage according to the loan agreement, how much total interest will you pay?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Value of the circuit impedance at the half-power

Find also (c) the bandwidth, (d) the lower and upper half-power frequencies and (e) the value of the circuit impedance at the half-power frequencies.

  Find current flowing through r6 = 12 ohm resistor

Voltage drop across R6 = 12 ohm resistor

  Determine the half-power or 3db bandwidth of the signal

signal s(t)= (2a) / (t2+a2) A) Determine the essential bandwidth B Hz of s(t) such that the energy contained in the spectral components of s(t) of frequency below B Hz is 99% of the signal energy.

  Find the cost of operating the toaster once per day

1.5- kW toaster takes roughly 3.5 minutes to heat four slices of bread. Find the cost of operating the toaster once per day for 1 month ( 30 days). Assume energy costs 8.2 cents/ kWh.

  Find the value of c in microfarads and l in henries

Find the total impedance ZT in polar form. -  Draw the impedance diagram. -  Find the value of C in microfarads and L in henries.

  Difference between synchronous and asynchronous machines

Investigate and produce a report on the main different logic families and their requirements - Describe with the use of circuit diagrams the difference between TTL (74 series) and CMOS (4000) integrated circuits.

  What is the probability that both will satisfy specification

A certain application specifies capacitors with resistances between 900 and 1,000 megohms.

  Why do you think we need both rectangular and polar forms

Why do you think we need both rectangular and polar forms. There still seems to be some confusion about the relationship between R, Xc, OR XI and the phase angle. Take a value for R and a value for XC that is ten times smaller than R and find the..

  Find the cavity dimensions and the resulting unloaded q

Find the cavity dimensions and the resulting unloaded Q.

  Describe how would design a gray code counter without vhdl

Explain why the low value (0) for the 'output' of a digital logic gate is lower than the low value for the 'input' of a digital logic gate (This is the case for CMOS and Bipolar logic). Look at a specsheet.

  Design a three mode pid controller

A liquid level system converts a 4-10 m level into a 4-20mA current. Design a three mode controller (PID im assuming) that outputs 0-5 volts with 50% PB, 0.03 min integration time, and 0.05 min derivative time. Fastest expected change time is 0.8 ..

  What are the limits on the output voltage produced

For this situa-tion, what are the limits on the output voltage produced? Assume rz = 20 rz and Iza = 0.2 mA for all available zeners.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd