Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
An induction motor has the following specifications: a 8-polesquirrel cage rotor, operates at 25 hp off of a 220 V line-to-line3-phase service, 60 Hz, 64 amps of line current, and under fullload runs at 830 RPM. The motor draws 20.8 kW at full load.
(i) Calculate the slip.(ii) Determine the percent speed regulation if the no-load speed is895 RPM.(iii) Determine the power factor of the induction motor.(iv) Determine the motor torque in ft-pounds.(v) Determine the percent power efficiency of this induction motor.
Perform the following addition or subtraction of the given numbers using 8-bit 2's complement representation of the numbers. Parts (a) and (b) are given in decimal, while parts (c)-(e) are given in 8-bit 2's complement. Indicate in each case wheth..
The current through a particular circuit element is given by i(t) = 10sin(200*pi*t) A. Determine the net charge that passes through the element between t=0 and t=10ms. Repeat for the interval t=0 and t=15ms.
Consider the BJT differential amplifier when fed with a common-mode voltage VCM . As is often the case, the supply voltage VCC may not be pure dc but might include a ripple component vr of small amplitude and a frequency of 120 Hz.
desgin a four-bit combinational circuit 2's complenmter.(the output generate complement of the input binary). then construct truth table for the input and correspondinf output. use kmap to find each outpt in terms of of inputs.
The display needs to tell you what direction you are about to move. The problem is WBNEC insists that you use a standard 7-Segment display. (Hint: You can tilt the display.) Design a decoder that will display up-down-left-right.
Draw a strain gauge circuit and its external components to attach to a conveyor mounted only at the ends to measure the load at the center of the conveyor. What type of testing would you need to do to establish a baseline and calibration curve for..
Calculate the maximum power that can be sent through an a=2cm , b=1cm air-filled waveguide at 12 GHz such that dielectric breakdown does not occur. Assume that the dielectric strength of air at atmospheric pressure is 3x10^6 [V/m]
Design a logic circuit to detect a winning tic-tac-toe pattern of three in a row. The output W=1 if a winning pattern is present. (Assume the X and O circuits are separate but identical) a. Design the X circuit for the following pattern of signals ..
e^-x=(1/e^x)=1/(1+x+(x^2/2)+(x^3/3!)+...) and compare with the true value of 6.737947*10^-3. Use 20 terms to evaluate each series and compute true and approximate relative errors as terms are added.
In a unity feedback system, the open-loop transfer function is of the form G_ol(s)=k/(1+s/Omega_p) Calculate the bandwidth of the closed-loop transfer function. How does the bandwidth depend on k and Omega_p
A buck converter has an input voltage that varies between 10 and 15 V and a load current that varies between 0.5 A and 1.0 A. The output voltage is 5 V. For a switching frequency of 200 kHz, determine the minimum inductance to provide for continuo..
A single-phase, 60-Hz power will be transmitted through the transmission line Each subconductor's radius is 10 cm. There are two configurations, the first one is setting subconductors A and B as a bundle, and C and D as another bundle
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd