Determine the molar fraction of the gas that condenses

Assignment Help Civil Engineering
Reference no: EM13300342

The stream from a gas well is a mixture containing 50 mol % methane, 10 mol % ethane, 20 mol % propane, and 20 mol % n-butane. This stream is fed into a partial conderser maintained at a pressure of 250 psia, where its temperature is brought to 80 degrees F. Determine the molar fraction of the gas that condenses and the compositions of the liquid and vapor phases leaving the condenser.

Reference no: EM13300342

Questions Cloud

Determine undrained shear strength on compacted soil sample : An unconfined compression test was conducted on a compacted soil sample, 50 mm diameter by 100 mm long. The peak axial force recorded was 230 N and the sample shortened by 2 mm.
Excisional biopsy of superficial lymph nodes : Excisional biopsy of superficial lymph nodes of the neck by means of an open procedure for non-hodgkin's lymphoma.....looking for cpt and icd codes...
Journalize all entries required on the given dates : Journalize all entries required on the above dates, including entries to update depreciation on assets disposed of, where applicable. Cleland Corporation uses straight-line depreciation.
Explain temperature you must first find the value of g0 : To find the value of the equilibrium constant at each temperature you must first find the value of G0 at each temperature by using the equation G0 = H0 - TS0 For this reaction the values are H0 = +88.3 kJ/mol and S0= 151.3 J/mol*K
Determine the molar fraction of the gas that condenses : The stream from a gas well is a mixture containing 50 mol % methane, 10 mol % ethane, 20 mol % propane, and 20 mol % n-butane. This stream is fed into a partial conderser maintained at a pressure of 250 psia
Refrigerator was only partially destroyed : Brian contracted to purchase a refrigerator from Big Buy, an electronics retailer. Big Buy agreed to deliver the refrigerator to Brian’s home. The truck delivering the refrigerator is hit by another truck and all of the contents were destroyed. Who b..
Calculate the percentage of chlorine in a sodium : Calculate the percentage of chlorine in a sodium hypochlorite powder if 5.0 kg of powder gives off 2.3 kg of chlorine.
How to calculate the equilibrium partial pressures of cl2 : Calculate the equilibrium partial pressures of Cl2, H2O, HCl, and O2. Peq(Cl2) = . Peq(H2O) = . Peq(HCl) = . Peq(O2) = . (b) Calculate KP for this reaction.
What is max mole fraction of methanol that can be achieved : A solution containing 30% methanol (by mol) is flashed to 1 bar, 70.82°C. Determine the phase of the system; if 2 phases, report the compositions and relative amounts of each phase.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What percent of the particles does the settling tank capture

The setting velocity of a particle is 0.002 m/s and the overflow rate of a settling tank is 0.008 m/s. (a) what percent of the particles does the settling tank capture. If the particles are flocculated so that thie rsettling rate is 0.05 m/s

  What is the tce concentration in mg per cubic meter

The concentration of trichloroethelyne (TCE) in an air sample near a hazardous waste landfill is 34 ppm, the ambient air temperature is 31 degrees C, and the atmospheric pressure is 0.94 atm. What is the TCE concentration in mg/m^3

  Determine horizontal distance between the points

What is the corresponding horizontal distance between the points - The slop distance 156.777 from one poin to another at rate of+1.5%

  Define soda ash and quicklime

Soda Ash and QuickLime, A lime-soda softening plant treats a flow of 150 MGD, and the water has 86mg/l Ca2+, 35 mg/L Mg2+, 299 mg/L HCO3- and 6mg/l CO2.

  What will be the volume

A sample of neon has a volume of 555 mL when it is at a pressure of 813 mmHg. What will be the volume when the pressure is increased to 1138 mmHg?

  Calculate the volume of gas produced

A 1-kg block of dry ice(solid CO2) becomes a gas at room temperature. calculate the volume of gas produced at 25 degrees celsius and 975 kPa.

  Calculate the largest tolerable internal crack length

Calculate the largest tolerable internal crack length for a 7075-T651 aluminum alloy component that is loaded to a stress one-half of its yield strength without catastrophic fracture. For the alloy, the plane strain fracture toughness is 24 and yi..

  Determine moment of inertia of beams cross-sectional area

Determine the moment of inertia of the beam's cross-sectional area about the x-axis. Set a = 40mm , b = 130mm , d = 110mm , h = 380mm .

  Sketch process on p-v diagram clearly labeling final states

5 Kg of water at 1.2 MPa, 120oC is contained in a frictionless piston-cylinder device. The water is heated until its temperature reaches 250oC. a) a)Determine the work performed in kJ

  What is the design storage and water surface elevation

What is the design storage and water surface elevation at the peak outflow rate and estimate the long-term average reduction (EPA, 1986) in particulates under dynamic conditions.

  What is the magnitude and direction of specific discharge

Groundwater moves through a sandstone porous media and is driven by a gradient of -0.05 directed at an angle of 60 degree counterclockwise from the x-axis.

  Chlorination tank for killing microorganisms

You are to design a chlorination tank for killing microorganisms in the effluent from a wastewater treatment plant. It is necessary to remove 99% of active bacteria in a wastewater flow of 120 m 3 /hr.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd