Determine the minimum speed and power to take off

Assignment Help Civil Engineering
Reference no: EM13318659

An airplane with a Clark Y airfoil cross-section weighs 3500 lbs. The chord length is 6ft and the wingspan is 36 ft.

Determine the: a) Minimum speed and power to take off, if the angle of attack is 12.4 degrees.

b) Power to cruise at 150 mph at an altitude of 15,000 ft.

c) % increase in power if the plane is cruising 150 mph at 10,000 ft.

d) Stall speed at landing

Reference no: EM13318659

Questions Cloud

Calculate the resistance of the arteriole : An arteriole has a length of 1.03 mm and a radius of 24.7 %u03BCm. Calculate the resistance of the arteriole
What is max velocity for boundary layer to remain laminar : A thin flat plate is 12 m long and 8 m wide. The air density is 1.23 kg/m3. a) What is the maximum velocity for the boundary layer to remain laminar over the entire plate (the transition occurs at the end of the plate)
Find the predicted value of velocity of the center of mass : you have a 100.00 cm track inclined at 10.000 degrees. You roll a steel ball down the track until it drops off the track and falls 1.0000 m to the floor
Uses rl or rc circuits in operation : Choose an application in business or industry that uses RL or RC circuits in its operation.
Determine the minimum speed and power to take off : An airplane with a Clark Y airfoil cross-section weighs 3500 lbs. The chord length is 6ft and the wingspan is 36 ft. Determine the: a) Minimum speed and power to take off, if the angle of attack is 12.4 degrees.
Calculate the height of the image : An object with a height of 2.49cm is placed 35.5mm to the left of a lens with a focal length of 34.2mm. What is the height of the image
An electromagnetic spectrum in order of decreasing frequency : Rank the following regions of the electromagnetic spectrum in order of decreasing frequency.X rays, Microwaves, Infrared, Ultraviolet A) infrared, microwaves, ultraviolet, x rays B) x rays, microwaves, infrared, ultraviolet C) microwaves, infrared..
What is the speed of one spaceship relative to the other : Two spaceships approach Mars from the same direction. One has a speed of 0.2c, What is the speed of one spaceship relative to the other
Design a circuit that implements the logic circuit : Design a circuit that implements the logic circuit using the fewest total number oflogic gates.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Long cantilever beam of elastic modulus

A 45 kg machine is placed at the end of a 1.6 m long cantilever beam of elastic modulus 200 x 109 N/m and cross-sectional moment of inertia 1.6 x 10-5 m4.

  Determine the maximum external pull the ferrari has

A ferrari with 808 hp has a max. speed of 211 mph at 6,300 rpm. the Ferrari weighs 4,155 lb/ton and is operated over a smooth concrete road with a rolling resistance of 40 lb/ton and a slope of 3%.

  Compute required weight of coarse aggregate per cubic yard

A concrete mix with a 3-inch slump, w/c ratio of 0.50, and sand with a fineness modulus of 2.4 contains 1700 lb/yd^3 of coarse aggregate. Compute the required weight of coarse aggregate per cubic yard.

  Design cyclone collection system which might meet the limits

Prepare a preliminary design of a system to collect dust from a plant under the following conditions: Sample of Dust: 50% by wt. below 30 micrometers; 80% by wt. below 70 micrometers Density= 2.5 g/cubic cmGas Flow Rate: 30,000 acfm (actual cubic fee..

  Determine the tensions in the cables and the reactions

The suspended load exerts a force F = 600 lb at A and bar OA weighs 200 lb. Assume that the bar's weight acts at its midpoint. Determine the tensions in the cables and the reactions at the ball and socket support O.

  Tackling the problem of making tunnel

You are a Project Manager on site where work for 3K.m. long Tunnel has been undertaken. The site is remote and takes about 2 days travel to nearest town. Supervisors, Technicians & Skilled Workers are engaged in dangerous / hazardous work.

  Draw the shear diagram for the shaft

Draw the shear diagram for the shaft. The bearings at and exert only vertical reactions on the shaft

  Estimate contact time to achieve an effluent concentration

Estimate the contact time to achieve an effluent concentration of 200 fecal coliforms/100 mL using a Cl2 dose of 3 mg/L if the wastewater temperature is 28 oC. Assume the activation energy (Ea) at pH = 7.4 is 6,500 cal/mole.

  What annual volume savings will wastewater achieve

The Pomdeterra wastewater treatment plant produces thickened sludge that has a suspended solids concentration of 3.8%. They are investigating a filter press that will yield a solids concentration of 24%.

  Determine elevation vs surface area relationship for vault

An underground storage vault is to be constructed to serve as a detention pond for a heavily urbanized area. The walls of the vault will be vertical, but the flow will be sloped along its length to promote drainage.

  What would be the estimated total annual dollar savings

what would be the estimated total annual dollar savings of a company with an annual direct labor payroll of 2,500,000 and a fixed overhead rate of 150 percent of direct labor , if the company initiated a methods and standards program

  Calculate the mass emissions rate of ash into the atmosphere

The coal has an ash content of 12% by mass. Forty percent of the ash falls out the bottom of the furnace. The rest of the ash is carried out of the furnace with the hot gases into an electrostatic precipitator (ESP).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd