Determine the minimum size of the pad footing 2 meters wide

Assignment Help Civil Engineering
Reference no: EM13544596

A geotechnical report has suggested an allowable bearing pressure of 200kPa. Determine the minimum size of the pad footing 2 metres wide for a steel column if a factor of safety of 2.0 is recommended (include an estimate of self weight of the footing in your calculations). The total load of the column is 447.644kN

Reference no: EM13544596

Questions Cloud

General systems theory encourages us to use a holistic : The evaluation of various possible scenarios (either future or past) using simulation models can be tremendously valuable as a tool used in strategic plan development.
Why you think the actual volume pumped in a real clean : A cylindrical volume of soil contaminated with trichloroethylene (TCE). It is about 2.5 m deep and about 4.0 m in diameter. The porosity of the soil is approximately 0.25.
Estimate the time between when the concentration ratios : A conservative tracer is applied to the ground surface and leached through the vadose zone by rainfall. The average volumetric water content is 0.40 over the upper 4 meters and 0.30 over the remaining 3 meters above the water table
Compute the required weight of coarse aggregate per cubic : A concrete mix with a 3-inch slump, w/c ratio of 0.50 and a sand with a fine modulus of 2.4 contains 1700 lb/cubic yard of coarse aggregate. Compute the required weight of coarse aggregate per cubic yard.
Determine the minimum size of the pad footing 2 meters wide : A geotechnical report has suggested an allowable bearing pressure of 200kPa. Determine the minimum size of the pad footing 2 metres wide for a steel column if a factor of safety of 2.0 is recommended
Estimate the amount of coal needed to light one 100-w : A 25-W compact fluorescent lightbulb (CFL) produces the light equivalent of a 100-W incandescent bulb. The population of North America is estimated to be about 305 million. Estimate the amount of coal needed to light one 100-W incandescent lightbulb
Calculate the hydraulic conductivity of silica sand : A constant-head permeability test was conducted on a sample of fine silica sand. The cross-sectional area of the sample was 60 cm2 and its length was 150 mm.
Calculate the horizontal scale factor and effective : The foundation soil for an earth dam has a horizontal hydraulic conductivity of 1.5 x 10-9 m/s and a vertical hydraulic conductivity of 1 x 10-10 m/s. It is proposed to estimate the seepage flow rate through the foundation soil using the flow net ske..
Determine the maximum tensile and compression stresses in : A 6ft wide, 10ft high vertical rectangular gate has its top edge 6ft below the water level. it is hinged along its lower edge. what force, acting on the top edge, is necessary to hold the gate shut?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Existing equal tangent sag curve

An overpass is being built over the PVI of an existing equal tangent sag curve. The sag curve has a 70 mi/h design speed, and G1 = -6%, G2 = +3%.

  Determine the ratio of the weight of the solid shaft

Two shafts are made of the same material and are of equal lengths.one of them is solid and another one is hollow. the ratio of inside and outside diameters for hollow shaft is 0.65.

  How much would end of wing deflect relative to fuselage

If the aluminum wing has an I of 745 in^4 and aluminum has an E of 10.1 *10^6 psi, how much would the end of the wing deflect relative to the fuselage of the aircraft compared to the position it has when aircraft is on the ground.

  Calculate the volume flow rate into the compressor

A 12kw (shaft output) motor is available to run a non-cooled compresor for helium. The pressure is to be increaded from 80 kPa to 120 kPa. If the compressor is 70% efficent, calculate the volume flow rate into the compressor.

  Describe why materials such as aluminum-steel and basswood

1. Describe why materials such as aluminum, steel, basswood, and Polystyrene Plastic and structures are important in our everyday lives. 2.Write a paragraph to explain to a lay person a few of the important factors

  Determine torque t indicated by a gage reading

A single strain gage is cemented to a solid 4-in diameter steel shaft at an angle B = 25 degrees with a line parallel to the axis of the shaft. Knowing that G = 11.6*10^6 psi

  Determine the the max weight of the block

Determine the the max weight of the block that the system does not fail if the max tension that can be developed in cable DB is 100N and the max compression that can be developed in tower CD is 100N.

  Design size of smoke vents in the ceiling with the objective

A storage room in an industry has a floor area of 30 m by 50 m and a height of 10 m. A garage door has a width of 3 m and a height of 3 m and the room has four windows that are 0.9 m by 0.9 m, situated at the height of 1 m from the floor.

  When the pressure drops across the basket strainer

Abasket strainer is installed in a 15-cm diameter pipe. Pressuregauges are installed immediately upstream and downstream of thebasket strainer. When water flows at 100 m3/hr, the pressure gaugeimmediately upstream of the basket strainer measures 1 ba..

  Determine the nominal flextural strength of the section

a rectangular beam with a width of a 8 in. an effective depth of 10 in., and a total depth of 12 in., is reinforced with a single fiberglass reinforcing bar that has a cross sectional area of 0.45 in^2.

  Calculate the dry unit weight of the compacted earth fill

During construction of a highway project, a soil sample was taken from compacted earth for a sand-cone in place denstiy test. The following data were obtained from the test. Weight of sand used to fill test hole and funnel of sand-cone device= 845..

  How much power is required to overcome aerodynamic drag

A new sports car has a drag coefficient of .30 and a frontal area of 21 ft^2, and is traveling at 110 mi/h. How much power is required to overcome aerodynamic drag if p=.002378 slugs/ft^3?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd