Determine the maximum shear flow in the channel

Assignment Help Civil Engineering
Reference no: EM131151619

The channel is subjected to a shear of V = 75 kN . Determine the maximum shear flow in the channel.

2099_81254ef2-f604-42c2-bd1e-9bf4a445b534.png

Reference no: EM131151619

Questions Cloud

Calculate the amount of power wasted and compare : Calculate the efficiency of this circuit and comment on it. Now, if we use a buck converter with an efficiency of 92%, see below: Calculate the amount of power wasted and compare that to the voltage divider circuit above.
What is reduced total meal time if you would make purchase : Suppose you want to spend the least amount of money to reduce the total meal time, which item would you purchase? What is the reduced total meal time if you would make the purchase?
Determine the shear flow at points a and b : The aluminum strut is 10 mm thick and has the cross section shown. If it is subjected to a shear of, V = 150 N , determine the shear flow at points A and B .
What are the most important considerations for him to weigh : How should Raja think about the situation? What are the most important considerations for him to weigh? How should they factor into his course of action
Determine the maximum shear flow in the channel : The channel is subjected to a shear of V = 75 kN . Determine the maximum shear flow in the channel.
Determine the location e of the shear center : Determine the location e of the shear center, point O , for the thin-walled member having the cross section shown. The member segments have the same thickness t .
What types of projects at company would favor pert over cpm : Explain the steps used to develop a forecasting system. How would these steps be specifically utilized by this company? What do you predict would be the result of implementing a forecasting system for the top-selling product line at this company? ..
Analyze the competitive advantage of each company : Analyze the competitive advantage of each company. Evaluate the strategies each company uses to create value and gain competitive advantage. Examine the measurement guidelines each company uses to verify its strategic effectiveness.
What are some of differences in the companies target market : What are some of the differences (if any) in the companies' target market? In your opinion, what are some of the strategies implemented by each company to help them to successfully reach their target audience

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the max distance between inlets

A suburban street receives storm water runoff at a rate of 2.0 L/m-s (one each side). the street has a slope of .8 percent and a cross slope of 2 percent, n = .013.

  Calculate the maximum value of w that may be supported

determine the ratio of l/a for plastic hinges to occur simultaneously in each span and at the supports. For this condition, calculate the maximum value of w that may be supported.

  Determine whether it has an fcc or bcc crystal structure

Rhodium has an atomic radius of 0.1345nm and a density of 12.41g/cm^3. determine whether it has an FCC or BCC crystal structure

  Determine the required diameter of the rod

A 4-m-long steel rod must not stretch more than 3 mm and the normal stress must not exceed 150 MPa when the rod is subjected to a 10- KN axial load.

  What minimum concentration must be achieved in tin pot

To study mixing of the stream and river, a conservative tracer is to be added to Tin Pot Run. If the instruments that measure the tracer can detect a concentration of 1.0 mg/L, what minimum concentration must be achieved

  Determine depth of zone of saturation below ground level

The natural ground water table at a site is located at a depth of 2m below the ground water. Laboratory tests reveal that the voidratio of the soil is 0.85 while the grain size corresponding to 10%finer is 0.05 mm.

  How many watts of power would it take to heat 1 l of water

How many watts of power would it take to heat 1 L of water(weighing 1.0 kg) by 10 degrees Celsius n 1.0 h? Assume no heat losses occur, so all of the energy expneded goes into heating the water.

  What is the water elevation upstream of the flume

Design a parshall flume to handle 24mgd in a 10ft wide channel at a downstream depth of 3 ft. If the channel floor is at elevation 65.7ft, what is the water elevation upstream of the flume

  Compute the crushing strength of concrete estimate the

The concrete cylinder 6 in x 12 in broke incompression at a load of 110000 lbs. Compute the crushing strength of concrete. Estimate the tensile strength and the modulus ofelasticity.

  Property of sanstone and of the quartzite

if you had a choice of three kinds of aggregate--a sandstone,a crushed basalt,and a quartizite,you may select the basalt.Give one possible characteristic or property of sanstone and of the quartzite that made you decide not to select it for your c..

  Draw the influence line for the shear in panel cd

Draw the influence line for the shear in panel CD of the girder. Determine the maximum negative live shear in panel CD due to a uniform live load of 500 lb/ft action on the top beams.

  Determine what is the largest value h should have

The dimension h is to be determined so that a worker can comfortably slide boxes weighing up to 100lb up and downa frictionless incline. If the worker can apply a 50lb horizontal force to the box

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd