Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Given: The 25mm thick strut shown below is glued to the horizontal member along surface AB. The glue can resist a shear stress of 600 kPa before failing, and the horizontal member can resist a normal stress of 2000 kPa before a bearing failure occurs.
Find: The maximum load P that can be applied if you want a factor of safety of 2.5 against glue failure and a factor of safety of 1.5 against bearing failure.
The gas flow rate is 1 kg m-2 s-1 of and the water entering is 1.6 kg m-2 s-1. For this system Henry's law holds and ye=1.75x, where ye is the mol fraction of A in the vapour in equilibrium with a mole fraction of x in the liquid.
air flows through a horizontal iron tube (e=0.15m) at Q=5.7x10-2 m3/s. find the pipe diameter if the pressure drop is 3.5kPa per 30.5m of pipe. air density = 1.23kh/m3 dynamic vicosity = 1.79 x 10-5 N.s/m2)
The receiver's velocity is constant at 10 yd/sec, and he catches passes when the ball is 6 ft. above the ground. If the quarterback desires the receiver to catch the ball 2.5 sec. after the launch instant, determine the initial speed v0 and angle,..
The minimum clearance between the roadway and the waterline must be 6 feet. The PVI is located at station 19+00.00 with elevation 420.50 feet. The design speed of the curve is 55 mph, g1 is +3%, and g2 is -3.0%. PRT= 2.5 sec, 0.35 = friction facto..
Write out the continuity and momentum equations that govern the surge travelling downstream. (Note: assume that the surge velocity exceeds the water velocity)
Water enters and leaves a pump in pipelines of the same diameter and approximately the same elevation. If the pressure on the inlet side of the pump is 30 kPa and a pressure of 500 kPa is desired for the water leaving the pump
A horizontal curve is being designed for a new two-lane highway(12-ft lanes). The PI is at station 250 + 50, the design speed is 65 mi/h, and a maximum superelevation of 0.07 ft/ft is to be used.
Water at 20ºC flows at a velocity of 2 m/s in a 200-mm diameter horizontal ductile-iron pipe. a) Estimate the friction factor in the pipe, and state whether the pipe is hydraulically smooth or rough.
The force F = 90i + 60j + 20k acts at the point (0,0,40). Compute the moment of the force about a line through the origin that has direction cosines (1/sqrt(3), 1/sqrt(3), 1/sqrt(3), 1/sqrt(3)).
write computer code using Matlab that emoloyes the nelder and mead simplex method to solve the welded-beam design (benchmark problem
If the column is subjected to an axial compressive force of 800 kN, determine the required diameter of each reinforcing steel bar so that one-third of the load is carried by the steel and two-thirds by the concrete. Assume Esteel= 200 GPa and Econ..
The specific weight of aire is .075 lb/ft^3. The physiological limit of the power for this well trained cyclist is .5 hp (1hp=550 ft*lbs/s) Neglect rolling friction, find the max speed of the bicycle.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd