Determine the mass of the refrigerant in the tank

Assignment Help Civil Engineering
Reference no: EM131031340

A 0.5-m3 rigid tank contains refrigerant-134a initially at 160 kPa and 40 percent quality. Heat is now transferred to the refrigerant until the pressure reaches 700 kPa. Determine (a) the mass of the refrigerant in the tank and (b) the amount of heat transferred. Also, show the process on a P-v diagram with respect to saturation lines.

Reference no: EM131031340

Questions Cloud

Student live on campus or off campus : (i) Does the student live on campus or off campus? (ii) What is the student's age in years? (iii) Ask how much money in coins (not bills) the student is carrying. (iv) Record the student's letter grade at the end of the course.
What is the equilibrium price of the good before trade : What is the equilibrium price of the good before trade? After trade, how many units of the good will be imported? How much did the consumer surplus grow with trade? How much did the total surplus grow with trade?
Remains inconsistent across the nations hospitals : In 1999, the Institute of Medicine report, To Err is Human, generated a brief flurry of concerns about avoidable hospital deaths. While progress has been made in addressing system errors and deficiencies, it remains inconsistent across the nation’s h..
Competition in quality and in service may be just as effect : 1. "Competition in quality and in service may be just as effective as price competition in giving buyers more for their money." Do you agree?  Why? 2.Explain why monopolistically competitive firms frequently prefer nonprice to price competition.
Determine the mass of the refrigerant in the tank : Determine (a) the mass of the refrigerant in the tank and (b) the amount of heat transferred. Also, show the process on a P-v diagram with respect to saturation lines.
Determining the proportion of heads : Set the probability of heads in the Probability applet to 0.5 and the number of tosses to 20. Click "Toss" to simulate 20 tosses of a balanced coin. What was the proportion of heads?
Based on this information, tangshan''s book value per share : At year end, Tangshan China Company balance sheet showed total assets of $60 million, total liabilities (including preferred stock) of $45 million, and 1,000,000 shares of common stock outstanding. Based on this information, Tangshan's book value per..
Question regarding the random mechanism : Problem: Random digits. The table of random digits (Table B) was produced by a random mechanism that gives each digit probability 0.1 of being a 0.
Determine the total heat transferred : Let the initial temperature vary from 150 to 250°C. Plot the final results against the initial temperature, and discuss the results.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the minimum possible area of the metal plate

A circular hole of diameter 11.42 + and - 0.03 inches is cut out of the plate. Also, using the tolerances given, determine the minimum possible area of the top surface of the metal plate.

  Horizontal compressive stress

1. The vertical compressive stress at a point in a soil is 100kN/m2 while the horizontal compressive stress at the same point is 57kN/m2. Both stresses are principal stress.

  Use the conveyance method to verify the results

A drainage channel had a cross section that may be approximated as a trapezoidal section with a bottom width of 15 feet and a side slope of 1.5H:1V. If the channel drops 2.5 feet per mile.

  What are the reactions-shear forces and bending moments

If you have 10 kips acting downward on a foundation and footing, 4 feet long, with uniformly distributed load acting up ward of 2.5 k/ft (soil) also 4 ft long. what are the reactions, shear forces, and bending moments at the tree critical points

  Estimate the time of submersion in years

A piece of corroded steel plate was found in a submerged ocean vessel. it was estimated that the original area of the plate was 62.5cm 2 and approximately 2.8k had corroded away during the submersion. Assuming a corrosion penetration rate of 5.1mm/yr..

  Determine the distance that a particle on the rim moves

The flywheel of a prototype car engine is under test. The angular position of the flywheel is given by x = (3.0rad/s3)t3 and the diameter of the flywheel is 36cm.

  Find the station and elevation of the low point of the curve

On a certain highway a -6% grade meets a +2% grade at station 70 + 00, elevation 550.97 ft. An equal tangent vertical curve, 800 ft. long, is to be installed to connect these two grades.

  Find the magnitude and location of the resultant force

You are to assume that seawater at 77oF will be used in the tank and the curved portion forms a quarter of a circle. The tank is open to the atmosphere. The overall height, h2, is 20ft deep. The radius of the curve, R, is 5ft. The width of the..

  Determine the distance dc

Three loads P1 = 2.4 kN, P2 = 4.4 kN, and P3 = 6.4 kN are suspended as shown from the cable ABCDE. Knowing that the maximum tension in the cable is 26 kN, determine the distance dC.

  Explain about pres-stressed concrete

Explain about pres-stressed concrete

  What is the average annual mass loading of pcb from

A lake has an area of 1000 ha. The concentration of the toxicant PCB in rainfall is 100 ng/l and the average annual rainfall is 70 cm. What is the average annual mass loading of PCB from the precipitation to the lake in kg/year.

  Magnitudes of fac and fad

The 70 m tall tower is supported by three cables that exert forces FAB, FAC, and FAD on it. The magnitude of the force FAB is 2 kN. The x and z components of the vector sum of the forces exerted on the tower by the three cables are zero. What are ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd