Determine the inlet volumetric flow rate

Assignment Help Civil Engineering
Reference no: EM13550309

Amomonia enters a refregeration system compressor operating at steady state at -18C, 138kPa. and exit at 150C, 1724kPa. The magitude of the power input to the compressor is 7,5kW and there is heat tranfser from the compressor to the surroundings at a rate of 0.15kW. Kinetic and potential energy are negligible. Determine the inlet volumetric flow rate , in m^3/kg, first using table A-15 and then assuming ideal gas behaviour for the ammonia.

Reference no: EM13550309

Questions Cloud

Find the magnitude and the direction of the third piece : A bomb at rest explodes, breaking into three pieces. Two of the pieces have equal mass and fly off at 60° to one another with the speed of 100 m/s. What are the magnitude and the direction of the third piece
The velocity with which they describe their orbit : Communication satellites are placed in a geosynchronous orbit i.e in a circular orbit such that they complete one full revolution about the earth in one sideral day (23.934h), and thus appear stationary with respect to the ground.
Choose a pipe to be used as a tension member to resist : Choose a pipe to be used as a tension member to resist a service dead load of 10 kips and a service live load of 25 kips. The ends will be connected by welding completely around the circumference of the pipe. The length is 8 feet. Use LRFD.
Compute the amounts for aerosmith company : Compute the amounts for Aerosmith Company: net sales, cost of goods purchased, cost of goods sold, gross profit, and net income.
Determine the inlet volumetric flow rate : Amomonia enters a refregeration system compressor operating at steady state at -18C, 138kPa. and exit at 150C, 1724kPa. The magitude of the power input to the compressor is 7,5kW and there is heat tranfser from the compressor to the surroundings at a..
Compute the depreciation expense under the method : Compute the depreciation expense under the methods for the year indicated - Straight-line for 2008.
Determine what is the thickness of the soap film : A thin soap film (n = 1.35) is suspended in air. The spectrum of light reflected from the film is missing two visible wavelengths of 490.8 nm and 589.0 nm, What is the thickness of the soap film
Which command in matlab is to delete all the variables : If variable Test(i,j) is selected so the first column represents the student number (1,2,..., 32), 2nd column represents the score of the first homework, 3rd column represents the score of the 2nd homework, etc. If there is a total of 6 homework for ..
Is it permissible to use darcys law under these circumstance : The water temperature is 14 C and the mean pore diameter is 0.33 mm. Is it permissible to use Darcy’s law under these circumstances? What is the reason for your answer?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find final temperature of steam and amount of mass transfer

A valve is now opened and steam at 1Mpa at 473 K is allowed to enter the cylinder until the volume inside increases to 0.04m^3 . Determine the final temperature of the steam and the amount of mass transfer

  Calculate the ammonia concentration in mg per l

NH4+ = N+ + NH3 pK =9.24 If the pH is 8.5 and the ammonium(NH4+) concentration in 20mg/L, calculate the ammonia(NH3) concentration in mg/L.

  Estimate the weight of concrete in four-lane highway segment

Estimate the weight of concrete in a four-lane highway segment that begins as a 3% grade climb from 1000 feet altitude to 4000 feet and then a 6% downgrade to 2500 feet

  Conclude that the mean cost of the new method is less

It is thought that a new process for producing a certain chemical may be cheaper than the currently used process. Each process was run 6 times, and the cost of producing 100-L of the chemical was determined each time.

  What is the significance of the splitting tensile strength

what is the significance of the (a) compressive strength of concrete, (b) splitting tensile strength, and (c) flexural strength of concrete

  Find principle stresses, max shear stress at a cross section

find principle stresses, max shear stress at a cross section 2 ft from the left of each locations: a) neutral axis, b) 2in. above neutral axis, c) the top of the beam.

  What would side slope of cut be if catch point is located

A backsight reading of 2.56 was obtained with rod at A and a foresight reading of 7.45 was obtained with the rod at the trial point B. If B is located 37.00 feet from the center line of a planned 50-foot wide road, is the catch point located uphi..

  Hat is the probability that more than 2.5 inches

what is the probability that less than 0.5 inches of precipitation will occur in any January? What is the probability that more than 2.5 inches wil

  What concentration of fe needed to maintain phosphate

FeCl3 is added to remove excess phosphate. The following reactions occur (the charges are in parentheses): FeCl3 -> Fe(3+) + 3Cl(-) Fe(3+) + PO4(3-) -> FePO4 The equilibrium constant for the second reaction is 10^26.4.

  Estimate the tension in the rope if the wind

The intensity of Na light passing through a gold film wasmeasured to be about 15% of the incoming light. What is thethickness of the gold film? ( λ=589 nm; k=3.2).

  Determine aeration period in hrs and f per m ratio

The 500- bed Lotta Hart Hospital has a small activated sludge plant to treat its wastewater. The average daily hospital discharge is 1200 L/day per bed, and the average soluble BOD5 after primary settling is 500 mg/L.

  Photovoltaic array and under insolation conditions

Photovoltaic array, Under insolation conditions of 500 W/m^2 (direct sunlight), and 10% solar cell efficiency

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd