Determine the exit temperature of the air and the rate of

Assignment Help Mechanical Engineering
Reference no: EM13633248

Hot air at atmospheric pressure and 80oC enters an 8-m long un-insulated square duct of crosssection 0.2mx0.2m and negligible thickness. The duct air passes through the attic of a house at a rate of 0.15m3/s. The duct surface is isothermal at 60oC. Determine the exit temperature of the air and the rate of heat loss from the duct to the attic space. Assume fully-developed flow in the duct throughout.

Reference no: EM13633248

Questions Cloud

The air in a bicycle tire is bubbled through water : the air in a bicycle tire is bubbled through water andcollected at 25 degrees celsius. if the total volume of gas
A random sample of 70 needles was taken from a medical : a random sample of 70 needles was taken from a medical manufacturing facility and 24 were found to be defective.
A wooden cylinder 300cm high floats vertically in a tub : according to archimedes principle the mass of a floating objectequals the mass of the fluid displaced by the object.
Suppose that a 614-ms wind is blowing across the roof of : suppose that a 6.14-ms wind is blowing across the roof of your house. the density of air is 1.29 kgm3. determine the
Determine the exit temperature of the air and the rate of : hot air at atmospheric pressure and 80oc enters an 8-m long un-insulated square duct of crosssection 0.2mx0.2m and
The wall thickness of 20 glass 2-liter bottles was measured : the wall thickness of 20 glass 2-liter bottles was measured by a quality control engineer. the sample mean was xbar4.05
The standard deviation of the lifetime of a sample of 15 : the standard deviation of the lifetime of a sample of 15 electric light bulbs was computed to be 98 hours and the
The intensity in wm2 of one sound is 694 times as great as : the intensity in wm2 of one sound is 6.94 times as great as the intensity of another sound. relative to the quieter
Compute the heat loss per one meter of pipe length now if : a pipe of negligible thickness has a hot fluid flowing inside it. it has a diameter of 0.6 m and a surface temperature

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A rigid 075 m3 tank initially contains water at 250oc 50

a rigid 0.75 m3 tank initially contains water at 250oc 50 liquid and 50 vapor by volume. a valve on the bottom of the

  A car is traveling at a constant speed of 35 mph what is

a car is traveling at a constant speed of 35 mph. what is the normal component of acceleration of the car at the top of

  Why use the penalty method for implementing boundary

why use the penalty method for implementing boundary conditions? what are the advantagesdisadvantages of direct versus

  Kinetic and potential energy effects can be ignored

one-tenth kilogram of water initially at 3 bar 200c undergoes a process to 15 bar 210c while being rapidly compressed

  A driver of a car is repeatedy driving around a roundabout

a driver of a car is repeatedy driving around a roundabout with a diameter of 100feet . the driver is traveling around

  Steam is flowing in a line at 100 bar it is flashed out

steam is flowing in a line at 100 bar. it is flashed out through a valve to 1 bar pressure. the temperature of the

  Ammonia enters the expansion valve of a refrigeration

ammonia enters the expansion valve of a refrigeration system at a pressure of 10 bar and a temperature of 248c and

  Determine the thermal efficiency and the mean effective

If the maximum temperature in the cycle is not to exceed 2200 K, determine the thermal efficiency and the mean effective pressure.

  Find the safe applied torque that can be transmitted

Find the safe applied torque that can be transmitted by the shaft ABCD, if the maximum shear stress in the hollow section is 47 MPa and G = 82.5 GPa.

  Dtermine the instantaneous rate of heat transfer from a

determine the instantaneous rate of heat transfer from a 1.5-cm-diameter ball bearing with a surface temperature of 150

  Steam enters a two-stage adiabatic turbine at 8 mpa and

steam enters a two-stage adiabatic turbine at 8 mpa and 550ordmc state 1 and is expanded to 2 mpa state 2 in the first

  Explain the velocity of the ball when it reaches the highest

A ball with a mass of 0.25 kg is thrown vertically upward with an initial velocity of 10 m/s. What is the velocity of the ball when it reaches the highest point?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd