Compute the heat loss per one meter of pipe length now if

Assignment Help Mechanical Engineering
Reference no: EM13633244

A pipe of negligible thickness has a hot fluid flowing inside it. It has a diameter of 0.6 m and a surface temperature of 165oC. It is in direct contact with air whose temperature is -18oC during the winter time. The air moves perpendicular to the steam pipe in cross flow with a free stream velocity of 5 m/s. Compute the heat loss per one meter of pipe length. Now, if the pipe is insulated with foam whose thermal conductivity is 0.04 W/(m K), compute the heat loss per unit length of pipe if the insulating layer has a thickness of 30mm.

Reference no: EM13633244

Questions Cloud

Determine the exit temperature of the air and the rate of : hot air at atmospheric pressure and 80oc enters an 8-m long un-insulated square duct of crosssection 0.2mx0.2m and
The wall thickness of 20 glass 2-liter bottles was measured : the wall thickness of 20 glass 2-liter bottles was measured by a quality control engineer. the sample mean was xbar4.05
The standard deviation of the lifetime of a sample of 15 : the standard deviation of the lifetime of a sample of 15 electric light bulbs was computed to be 98 hours and the
The intensity in wm2 of one sound is 694 times as great as : the intensity in wm2 of one sound is 6.94 times as great as the intensity of another sound. relative to the quieter
Compute the heat loss per one meter of pipe length now if : a pipe of negligible thickness has a hot fluid flowing inside it. it has a diameter of 0.6 m and a surface temperature
By what factor does the rate of the reaction with the : by what factor does the rate of the reaction with the followingrate law change if the concentrations of no2 andcl2 are
What voltage would you expect based on the joule tomson : what voltage would you expect based on the joule tomson coefficient value for co2 if op amp is set to 100 for a
A methanol fuelled turbocharged north american racing : a methanol fuelled turbocharged north american racing series engine has the following specificationfour strokeengine
What volume of h2 could be produced at atemperature of 13 : 1 what is the molar mass of a substance that is 22.3 n bymass and one molecule contains 2 nitrogen atoms?2 what is the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the magnitude of the resultant force acting at a

The roof is supported by cables. If the cables exert FAB = 100N and FAC = 120N on the wall hook at A, determine the magnitude of the resultant force acting at A.

  A construction crew lifts about 560 lb of material serveral

a construction crew lifts about 560 lb of material serveral times during the day from a flatbed truck to a 32 foot

  Heat in the amount of 100 kj is transferred directly from a

1. air is compressed by a 30 kw compressor from p1 to p2. the air temperature is maintained constant at 25 oc

  Given the absolute roughness of the pipe is 026 mm density

a new cast iron pipe is 5 km long and 15 mm diameter is used to convey water at a rate of 0.0150m3s-1. given the

  What angle acompensates for the wind such that the shell

a fireworks shell is launched vertically from point a with speed sufficient to reach a maximum altitude of 500 ft. a

  Determine the nature of the first phase change that

one litter of iodine vapour at 0.04 atm pressure and 150c is isothermally compressed. a. determine the nature of the

  An irregularly shaped object weighs 100 lb in air and 64

an irregularly shaped object weighs 100 lb in air and 64 lb when fully submerged in water. determine the volume and

  Derive the operational transfer function

Derive the operational transfer function and the sinusoidal transfer function for an RC high-pass filter. Plot the step response and the complete frequency response (magnitude and phase).

  The plates leave a heat treatment oven 300 c and ambient

a flat steel plate is 1 m long and 1 m wide. air flows over the plate at 10 ms. the plates leave a heat treatment oven

  Find the corresponding damping coefficient

Find the corresponding damping coefficient c. Identify the system parameters such as the natural frequency and damped frequency. Derive the mathematical expression of the displacement as a function of time with the given initial condition. Plot yo..

  The power output of the turbine is 25 mw neglecting changes

steam enters an adiabatic turbine steadily at 8 mpa and 500 c through an inlet with cross-section area of 0.041767 m2

  The vale is open and the two gases are allowed to mix

two tanks a and b are connected by a short section of pipe with a valve that is initially closed. both tanks are

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd