Determine the elevation and stationing of the low point

Assignment Help Civil Engineering
Reference no: EM13312112

A 1600-ft-long sag vertical curve (equal tangent) has a PVC at station 120+00 and elevation of 1500 ft. The initial grade is -3.5% and the final grade is +6.5%. Determine the elevation and stationing of the low point, PVI and PVT.

Reference no: EM13312112

Questions Cloud

Description of the facts of the investigation and case : Need to make report on small cases- 7 cases altogether in 1 assignment. 2 assignment has 7 cases as well.
What is the maximum speed of the block : A block of mass m = 4.43 kg is attached to a spring which is resting on a horizontal frictionless table. What is the maximum speed of the block
Find how many trucks are needed to service the backhoe : A haul fleet of trucks having a heaped capacity of 15 cy. is to be loaded by a hydraulic backhoe excavator (CT=.48 min.) with a 3 1/2 cy. heaped capacity. Assume the material is a wet loam that weighs 3380 lb/cy in the bank state
Find the the magnitude of average drag force exerted on car : A 7450-kg car is travelling at 28.7 m/s when the driver decides to exit the freeway by going up a ramp. find the magnitude of the average drag force exerted on the car
Determine the elevation and stationing of the low point : A 1600-ft-long sag vertical curve (equal tangent) has a PVC at station 120+00 and elevation of 1500 ft. The initial grade is -3.5% and the final grade is +6.5%. Determine the elevation and stationing of the low point, PVI and PVT.
Inventory and lean manufacturing : Inventory and Lean Manufacturing
What is the current draw of the motor during the operation : The motor has an efficiency of 80%. It operates at 240V AC. A 12" diameter drum is attached to the gearbox output shaft, and a wire rope is wrapped around the drum to act as a winch. The winch is used to raise bucket of raw material in a factory.
Determine what is the new flowrate of the channel : The flowrate through an open channel with a slope of 2 % is calculated using Manning's equation at 100 cubic feet per second. If the slope of the channel is doubled to 4%
Introduction and background of your ce : Introduction and background of your CE

Reviews

Write a Review

Civil Engineering Questions & Answers

  What mineral is mined from under the city of detroit

For some minerals color is a diagnostic property making identification rather easy. However, certain minerals can also occur in a wide variety of colors making color a poor tool for identification. List different colors for the mineral quartz lo..

  Determine what is the volume change of the tube

a circular aluminum tube of L=600 mm is loaded in compression by forces P. The outside and inside diameters are d2=75 mm and d1=63mm, respectively. A strain Gage is placed on the outside of the tube to measure normal strains in the longitudinal di..

  Write expression for engineering strain associated with a

A piece of wire is stretched from length l1 to length l2 (step A), and then from length l2 to length l3 (step B). (i) Write down an expression for the engineering strain associated with step A.

  Determine the actual field weight required to mix a 4 bag

Determine the actual field weight required to mix a 4 bag mix using the mix proportions given below. The excess moisture contet of the sand is 6% and that of the gravel is 2% Component Weight ..

  Calculate the decay rate of radon in units of hr-1

Indoor Air quality is greatly affected by Radon, which can cause lung cancer. When we moved to Colorado, we tested the house for Radon and installed a radon mitigation system.

  Determine the new angular speed with moment of inertia

Person spining has his arms outward. The moment of inertia is 52kg*m^2 and ang. speed 3.80 revolutions/ second. if the persons arms are down. moment of inertia goes to 35kg*m^2. find the new angular speed

  Design a portland cement concrete mix for a loading clock

Design a Portland cement concrete mix for a loading dock driveway slab. The concrete will be exposed to deicing chemicals and subjected to freezing and thawing in a moist condition. This is severe environmental exposure.

  Determine what the height should be to force to be critical

Given that uniform flow is subcrital and there is a weir in a rectangular channel, how do you determine what the weir height should be to force the flow to be critical. Draw this transition on a specific energy curve.

  What ration of lengths will cause the maximum shear stress

A solid circular shaft AC of total length L=L1+L2 is fixed against rotation at ends A and C and is loaded by a tourqe T_b at joint B. If the diameter of the two segements of the shaft are in ratio d2/d1

  Determine what is the resulting solids concentration

Raw primary sludge at a solids concentration of 4% is mixed with waste activated sludge at a solids concentration of 0.5%. The flows are 20 and 24 gal/min, respectively. What is the resulting solids concentration

  Determine how large must the reactor be

A CMFR is to be designed to remove contaminant A from water with a steady-state efficiency of 95 percent. The decay reaction is zeroth order, with a rate constant of 0.1M/h. The inlet concentration of A is 0.5 M.

  Determine force necessary for system to be in equilibrium

The mass of each pulley of the system is 50 kg, and mass of the suspended object A is 160 kg. Determine the force necessary for the system to be in equilibrium? Be sure to draw complete free body diagram(s) for full credit.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd