Determine the elastic elongation that would be expected

Assignment Help Civil Engineering
Reference no: EM13307824

A load test on a 4.5-mm-diameter by 125-mm-long magnesium alloy rod found that a tension load of 831 N caused an elastic elongation of 0.47 mm in the rod. Using this result, determine the elastic elongation that would be expected for a 16-mm-diameter rod of the same material if the rod were 1.6 m long and subjected to a tension force of 3.3 kN.

Reference no: EM13307824

Questions Cloud

Find what is the second year book value for equipment : what is the second year book value for equipment with an initial cost of $11,000, a salvage value of 1,000 and a recovery period of 5 yrs for A. straight line depreciation. B. Double declining balance. C. MACRS
The carnegie approaches to decision making : What are the differences between the rational and the Carnegie approaches to decision making? What are the differences between the incrementalist and the garbage can models?
How many total bits are required for a direct-mapped cache : How many total bits are required for a direct-mapped cache with 16 KB of data and 4-word blocks, assuming a 32-bit address.
How many kegs of nails should low order at one time : Using the EOQ method, how many kegs of nails should Low order at one time? EOQ = square root 2DB/IC.
Determine the elastic elongation that would be expected : determine the elastic elongation that would be expected for a 16-mm-diameter rod of the same material if the rod were 1.6 m long and subjected to a tension force of 3.3 kN.
Compute the total heat flow into the gas : An ideal gas expands at a constant pressure of 2.1 atm from 446 mL to 844 mL. Heat then flows out of the gas, What is the total heat flow into the gas
Determine the change in each lateral dimension : At the proportional limit, a 32-mm-thick by 87-mm-wide bar elongates 10.2 mm under an axial load of 532 kN. The bar is 2.4 m long. Poisson%u2019s ratio, , for the material is 0.27.
Marketing plan for the purpose of expanding the distribution : Martha Stewart Living Omnimedia and Hain Celestial Group have hired you to develop a marketing plan for the purpose of expanding the distribution of their "Martha Stewart Clean" line of eco-friendly cleaning products to the regions of Asia and South ..
Write a complete c++ program that reworks your cellular bill : Write a complete C++ program that reworks your Cellular Bill calculation program from Chapter 4. Give your source file a meaningful name, such as CellBillFun.cpp.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the over consolidation ratio of the soil

an increment of vertical stress of 150kpa compress the sample to a void ratio of1.43. what is the over consolidation ratio of the soil at the unloaded condition.

  What thickness of bc will result in same compressive stress

A second load P2 is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the post are dAB= 1.25 in, tAB= 0.5 in, dBC= 2.25 in and tBC= .375 in respectively.

  What is the allowable minimum length of the ramp

Using the ADA code, what is the allowable minimum length of the ramp base if base if it is 2 ft high and the code is 1:12

  Calculate force and moment

Which software do we use to calculate force and moment, and draw shear and moment diagram? I really need this software to design my structural project. Please helps me... thank you so much.

  Find how much must be deposited now if the fund will earn

The maintenance costs begin in 31st year at $300,000 annually. How much must be deposited now if the fund will earn 5% interest. How much does this change if the interest rate is 4%

  Determine maximum allowable compressive force can be applied

The force is applied at the two pins. The pins allow rotation around the z-axis and do not allow rotation around the y-axis. The length of the beam between the pins is 8m. Determine the maximum allowable compressive force that can be applied.

  Compute evaporation rates in the winter and in the summer

At a certain location during the winter, the average air temperature is 10 degrees celcius and the net radiation is 40W/m^2 and during the summer the net radiation is 200W/m^2 and the temperature is 25 degrees celcius.

  Discuss about damp-proofing trenches

Discuss about damp-proofing trenches

  What are the position and acceleration of body as functions

The velocity of a body is given by v(t) = 2t+t3. The body starts from rest at time t = 0 at position s(0) = (2,-10). What are the position and acceleration of the body as functions of time At what time, t, does the body cross the X-axis

  What are critical depth and normal depth at given discharge

a low broad crest weir is installed in a wide, rectangular channel to reduce the flow velocity. the channel is 60ft wide, the channel slope is 1 to 2000. Manning's roughness coefficient n=0.014. the discharge per unit channel width is q=60 cfs/ft.

  Types of metamorphic foliations

Name three types of metamorphic foliations, and draw a small sketch that shows a situation. Where a metamorphic foliation could cause problems in an excavation.

  Explain the difference between piezometer and tensiometer

Briefly explain the difference between piezometer and tensiometer with respect to the working principle, special design consideration and limitation of the instrument.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd