Determine the discharge temperature and the power required

Assignment Help Mechanical Engineering
Reference no: EM13640436

A steady flow, steady state air compressor handles 4000 ft3/min measured at the intake state of 14.1 psia, 30.0°F and a velocity of 70.0 ft/s. The discharge is at 45.0 psia and has a velocity of 280 ft/s. Both the inlet and exit stations are located 4.00 ft above the floor. Using the specific flow availability relative to the local environmental (ground state) temperature of 80.0°F and a pressure of 14.7 psia, determine:

a. The discharge temperature and the power required to drive the compressor if the process irreversible and adiabatic.

b. The discharge temperature and the power required to drive the compressor if the process is irreversible and adiabatic with a compressor work transport efficiency of 80.0%.

Reference no: EM13640436

Questions Cloud

A sample of the monthly amounts spent for food by families : a sample of the monthly amounts spent for food by families of four receiving food stamps approximates a symmetrical
A speedboat starts from rest and accelerates at 201 ms2 for : a speedboat starts from rest and accelerates at 2.01 ms2 for 7.30 s. at the end of this time the boat continues for an
If the process is not reversible but is adiabatic and : a steady flow air compressor takes 5.00 kgmin of atmospheric air at 101.3 kpa and 20.0degc and delivers it at an exit
Both the velocity and acceleration of the motorcycle point : a motorcycle has a constant acceleration of 2.4 ms2. both the velocity and acceleration of the motorcycle point in the
Determine the discharge temperature and the power required : a steady flow steady state air compressor handles 4000 ft3min measured at the intake state of 14.1 psia 30.0degf and a
If 0186 kg of chromium is deposited on a bumper in 105 min : conducting objects can be chrome-plated by immersing them in an electrolytic bath having positive chromium ions in
Determine the steady state irreversibility rate of each : the surface temperature of a 100 w incandescent lightbulb is 60.0degc. the surface temperature of a 20.0 w fluorescent
The moon has a mass of 736 x 1022 kg and a radius of 174 x : the moon has a mass of 7.36 x 1022 kg and a radius of 1.74 x 106 m.a what is the acceleration due to gravity on the
The following random sample of annual salaries was recorded : 50524846325147205349the following random sample of annual salaries was recorded. units are in thousands of dollars.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine a the proper distance between compressor

a natural gas methane pipeline is to be designed to transport the gas at a rate of 50000 scfm. the pipe is to be 6

  Determine the number of revolutions

Determine the number of revolutions that the motor executes in a) reaching its rated speed, b) coasting to rest.

  Calculate the strain-rate sensitivity or m value for al

a strain-rate dependence test is conducted on samples of al 6061-t6. two identical bars are tested. the first bar is

  Determine the torque t and power p that can also act

a solid shaft 200 mm in diameter rotates at f 20 revsec and is subjected to a bending moment of 21p kn.m. determine

  Suppose we load this cart with a crate of mass 104 kg where

you are given a four-wheeled cart of mass 15 kg where the distance between a wheel and its nearest neighbors is 2 m.

  Determine the required stiffness k of the hydraulic

the jet engine mass m 400kg of a passenger airplane is attached to the planes wing by a connector that has an

  What is the concept they understood

To solve ax = b Find a number y such that ay is integer (and possibly a factor of b) Then if k Ay = b, the answer is ky What is the concept they understood?

  What is the distance between the hook ends if the spring is

a helical tension spring is made of 1.2 mm wire having a yield strengths of 1280 mpa tension and 740 mpa torsion. the

  Describe the relationship between microstructure scale and

1. describe the relationship between microstructure scale and material properties. provide an example for how

  The work input is measured to be 4854 kjkg knowing the

steam is compressed by a compressor from 120oc and 150 kpa to 200oc and 1.5 mpa. the work input is measured to be 485.4

  An adiabatic capillary tube is used in some refrigeration

an adiabatic capillary tube is used in some refrigeration systems to drop the pressure of the refrigerant from the

  Determine the average temperature of the cooling water can

a cylindrical nuclear fuel rod of 1 cm in diameter is encased in a concentric tube of 2 cm in diameter where cooling

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd