Determine the bar centroid for the cone from a single scoop

Assignment Help Civil Engineering
Reference no: EM13319482

A single-scoop ice cream cone is a composite body made from a single scoop of ice cream placed into a cone. Assume that the scoop of ice cream is a sphere with radius r = 1.67 in that is placed into a 4.00 in tall cone. The interior height of the cone is 3.60 in. The cone has an exterior radius of 1.25 in and an interior radius of 1.10 in. The scoop of ice cream sits on the cone's interior radius and extends into the cone some distance. Find the bar {z} centroid for the cone (the scoop of ice cream and the cone).

Reference no: EM13319482

Questions Cloud

What is the width of the central bright fringe : A two-slit pattern is viewed on a screen 1.05 m from the slits. If the two third-order minima are 25.0 cm apart, what is the width of the central bright fringe
How to calculate the molarity of the solutions : Calculate the molarity of the following solutions. a) 0.600 mol of Na2S in 1.40 L of solution. b) 20.1 g of MgS in 851 mL of solution.
What is the pressure applied to the soil under above load : what is the pressure applied to the soil under the above load. How does this compare with an allowable bearing capacity of 100kPa. Does this allow for a reasonable factor of safety.
Determine the minimum required depth of the beam : A simply supported beam (one end has a pin support and the other a roller support) is 10 ft long. The width of the beam is 3.5 in. The beam supports three concentrated loads
Determine the bar centroid for the cone from a single scoop : The interior height of the cone is 3.60 in. The cone has an exterior radius of 1.25 in and an interior radius of 1.10 in. The scoop of ice cream sits on the cone's interior radius and extends into the cone some distance.
Explain reactant will remain after the reaction is complete : CaCO3(s)+2HCl(aq) -> CaCl2(aq) +H2O(l) +CO2(g) How many grams of calcium chloride will be produced when 27.0 g of calcium carbonate are combined with 12.0 g of hydrochloric acid. Which reactant is in excess and how many grams of this reactant will..
What is the focal length of the rearview mirror : The right-side rearview mirror of Mike's car says that objects in the mirror are closer than they appear. What is the focal length of the rearview mirror
Write summary on the front movie by woody allen : Write a one page summary 300 words that contains main points and your opinion about the movies - the Front movie by Woody Allen
Due to potential problems with its breaking system : Antonio, an accountant working for the city of Santa Cristina,decides to forego his annual vacation to Hawaii when word leaks out that the city may be cutting all employees’ salaries by 10 percent at the end of the year

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine distance the officer traveled before overtaking

The officer believes the driver is intoxicated and begins accelerating uniformly to 50 mi/h in 8 seconds and maintains a constant velocity of 60 mi/hr, overtakes the motorist 42 seconds after he passed the officer.

  Determine the location of the center of gravity of the cast

determine the location of the center of gravity of the cast aluminum block

  Calculate pressure in point 1 nd density of manometric fluid

A U manometer reads 20 cm air as operating fluid and a given manometric fluid. A single branch closed tube reads 35 cm connected to point 1. If P2 = 1.2 ATM calculate the pressure in point 1 and the density of the manometric fluid.

  Determine percentage of truck as seen by stationary observer

From a photograph one observs that on a level section of highway 20% of the vehicles are trucks, 80% are cars, and that there are 50 vehicles per mile of highway. The trucks travel at 40 mph, the cars at 50 mph.

  What is the reason for the relatively high strength of wood

what is the reason for the relatively high strength of wood in the longitudinal direction of the tree trunk as compared to the transverse direction

  How to determine maximum positive factored design moments

How to determine maximum positive and maximum negative factored design moments at a certain point

  Draw the shear diagram for the shaft

Draw the shear diagram for the shaft. The bearings at and exert only vertical reactions on the shaft

  What is maximum unstretched cord to avoid reaching creek

Assume that the cord used in a bungee jump behaves like a linear spring when it is stretched with a spring constant of 80 lb/ft. A 180 lb student is going for a bungee jump off the Canyon Creek bridge in Washington state.

  Determine the magnitudes of the components faa and fbb

Force F with magnitude indicated acts at point o. determine the magnitudes of the components Faa and Fbb along directions a-a and b-b so that F=Faa+Fbb

  Dry unit weight of material

A soil borrow material in its natural state in the ground has a unit weight of 118pcf. Its natural water content is 7%. What is the dry unit weight of this material?

  Design the pipe to flow capacity and use a mannings n

Determine the diameter (in inches) and velocity (feet per second) of a concrete storm pipe required to carry a peak flowrate of 20 cfs at a slope of 1.0% Design the pipe to flow at 75% capacity and use a Mannings n of 0.013.

  Determine the size and power requirements for rapid mix

A water treatment plant is processing water at s flow rate of 0.26m^3/s. The hydraulic detention times for the rapid mix tank, flocculation basin and the rectangular sedimentation basin are 10 sec, 30 min, 60 min, respectively.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd