Determine the average velocity for the portion

Assignment Help Civil Engineering
Reference no: EM13561540

1.An incompressible fluid flows horizontally in the x-y plane with a velocity given by v = 20 (z/h)^(1/3),where z and h are in meters and h is a constant.

Determine the average velocity for the portion of the flow between z= 0 and z=h. Answer is between 10 and 20 m/s

Reference no: EM13561540

Questions Cloud

International case analysis assignment : International Case Analysis Assignment
How much will the temperature of the tank change if the heat : You have been asked to prepare a salt solution using 18.5 grams of NaCl and 6 gallons of water, What will the weight percent salt be in the resulting solution? 1 gallon = 3.78 liters
Product strategy : Product Strategy
Estimate the elastic shrinkage,and total axial deformation : Estimate the elastic, shrinkage, and total axial deformation of a concrete column after 2 years of permanent load application.  Assume the full structural load was applied at 28 days after placing concrete.
Determine the average velocity for the portion : An incompressible fluid flows horizontally in the x-y plane with a velocity given by v = 20 (z/h)^(1/3),where z and h are in meters and h is a constant.
Describe how it has penetrated corporate : a.Describe how IT has penetrated corporate and government administrative systems.
Determine the clean filter head loss in a filter bed compose : Determine the clean filter head loss in a filter bed composed of 0.3 m of uniform anthracite (with an average size of 1.6 mm) placed over 0.3 m of uniform sand ( with an average size of 0.5 mm)
What is the rate of leakage in gallons per day : Evaporation from a nearby lake was 8 in. during June. It is estimated that 25 percent more will evaporate from the pool than the lake. On July 1, the pool is 5 inches below the top. Does the pool have a leak? If so, what is the rate of leakage in gal..
Develop a strategy for communicating high expectations : Develop a strategy for communicating high expectations

Reviews

Write a Review

Civil Engineering Questions & Answers

  What will be the depth when the discharge is given

Plot a graph showing the discarge per unit width per unit width q for various depths if the specific energy remains constant at this value. What will be the depth when the discharge is 1/3 of the discharge at critical depth

  Determine the net power output of the engine

The cycle has a thermal efficiency of 35%, and steam changes from saturated vapor at 300 C during the heat addition process. If the mass flow rate of the steam is 2kg/s, determine the net power (kw) output of this engine.

  Determine the magnitudes of the other forces

A welded connection is in equilibrium under the action of thefour forces shown. Knowing that Fa=8kn and Fb= 16kN, determine the magnitudes of the other forces.

  Calculate the coefficient of volume compressibility

In an oedometer test, the void ratio of a clay sample changed from 1.62 to 1.41 as the vertical effective stress imposed on the sample was increased from 100 kPa to 200 kPa.

  How to achieve a flow rate of 1 cfs at an elevation

Size an orifice and a weir for problem 2 on page 398 and 399 of the text book to achieve a flow rate of 1 cfs at an elevation of 102.5 feet and a total flow rate of 50 cfs at an elevation of 106 feet

  What is the equilibrium droplet size at a relative humidity

Design a hollow steel shaft with an inside diameter 1/3 that of the outside diameter. The shaft transmits 200 kW at a speed of 20 Hz. The allowable shearing stress is 55 MPa, and the allowable angle of twist is 1 degree per meter of length.

  Find the maximum cargo weight that the barge can carry

Assume you are responsible for determining the maximum load that can be carried by a rectangular barge that is 8 m wide and 18 m long. The water line when the barge is empty is 3 m below the level of the cargo deck.

  Why is a length of about 1.25l bridge segment is constructed

In the construction of a two-span bridge (span length = L) by using span-by-span construction, why is a length of about 1.25L bridge segment is constructed in the first phase of construction?

  How high can the hump be made without backing flow up

A smooth hump is placed in the bottom of the channel. What would be the depth of flow over a 3 ft high jump. How high can the hump be made without backing flow up What would be the depth of flow over and just upstream of a 6 ft high jump

  Determine the force and couple at o equivalent to the two

Head loss and sunshine striking a pipeline cause the temperature of the water flowing inside to rise by 2 degrees Celsius between two measuring points. Find the heat gain in J/N and cal/N.

  Which of the available soils appears to be most promising

A sanitary landfill project needs an import soil for use as an impervious cap over the refuse. The design engineer desires a soil with a high clay content because it will help keep water out of the landfill.

  Solve for deflection and reactions using partitioned form

For the FE pin-pin cable model, solve for the deflection and reactions using the partitioned form. What is partitioned form

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd