Determine the average molar mass of the mixture

Assignment Help Civil Engineering
Reference no: EM131034277

The combustion of a hydrocarbon fuel with air results in a mixture of products of combustion having the composition on a volume basis as follows: 4.89 percent carbon dioxide, 6.50 percent water vapor, 12.20 percent oxygen, and 76.41 percent nitrogen. Determine the average molar mass of the mixture, the average specific heat at constant pressure of the mixture at 600 K, in kJ/kmol -K, and the partial pressure of the water vapor in the mixture for a mixture pressure of 200 kPa.

Reference no: EM131034277

Questions Cloud

How it specifically impacts the creation of digital media : Describe each practice, explain why it is a best practice, and then relate it to how it specifically impacts the creation of digital media within chosen specialization, as opposed to only providing general content that could apply to any digital m..
Although aluminum chloride alcl3 is ionic : Although aluminum chloride AlCl3 is ionic in the solid state is molecules in the gaseous State write the Lewis structure prepare a VSEPR sketch describe the geometry prepare a VB sketch and describe the bonding in gaseous AlCl3
Determine the heat transfer during this process : A piston-cylinder device contains 6 kg of H2 and 21 kg of N2 at 160 K and 5 MPa. Heat is now transferred to the device, and the mixture expands at constant pressure until the temperature rises to 200 K.
Describe the physical motion of the fluid : Describe the physical motion of the fluid and the main modes of heat transfer in each section (I through IV) of the following figure
Determine the average molar mass of the mixture : Determine the average molar mass of the mixture, the average specific heat at constant pressure of the mixture at 600 K, in kJ/kmol -K, and the partial pressure of the water vapor in the mixture for a mixture pressure of 200 kPa.
A power of attorney is best described : A "power of attorney" is BEST described as:A. An oral employment contract between a principal an agent
Some agents are classified as servants : Some agents are classified as "servants" while others are classified as "independent contractors." Which of the following best describes the main difference between these two kinds of agents?
Develop a valid musical aptitude test than a reliable one : Describe how you would standardize your test and assess reliability and validity. Explain why it may be more difficult to develop a valid musical aptitude test than a reliable one.
The articles of incorporation of a corporation : Which of the following would normally be included in the Articles of Incorporation of a corporation?I. Name of the corporation

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the water content of this borrow material

A soil borrow material in its natural state in the ground has a unit weight of 85 pfc. When a sample of this soil is dried in the laboratory, its dry unit weight is 72 pfc.

  Determine perpetual equivalent annual worth with landscaping

The cash flow associated with landscaping and maintaining a certain monument in Washington, D.C., is $100,000 now and $50,000 every 5 years forever. Determine its perpetual equivalent annual worth

  Determine the change in storage during month of september

The average flow rate of the River Tiger into the lake was determined to be 3.5 m3/s and the average flow rate of the River Yankee out of the lake was measured at 2.5 m3/s (ignore any loses due to evapotranspiration).

  Determine the velocity of the particle as a function of time

a particle moving along a straight path decelerates according to a = -kv. this represent a drag-induced deceleration. assume that the intial velocity is vo at t=0 and s = 0. determine the velocity of the particle both

  Calculate the specific weight of the material

Your engineering consulting firm has been asked to determine the specific weight of an unknown material. You decide to use the concept of buoyancy to figure this out. So you weigh the material in both air and water.

  Determin the force in memebers de-hg and he of the stress

determin the force in memebers de, hg and he of the trees and state if the members are in comperhemsion

  Location and magnitude of the maximum vertical deflection

Find the location and magnitude of the maximum vertical deflection - Find the deflection under the load using the Moment-Area Method

  What is the allowable slope angle at a factor of safety

A cutting 9 m deep is to be excavated in saturated clay of unit weight 19 kN/m3. The design shear strength parameters are cu = 30 kN/ m2 and fu = 0. A hard stratum underlies the clay at a depth of 11 m below ground level.

  Find the probability that the drawn marble is blue or red

A marble is drawn at random from a box containing 10 red, 30 white, 20 blue, and 15 orange marbles. Find the probability that is: (a) orange or red (b) not red or blue (c) not blue (d) white (e) red, white, or blue

  Calculate the required downpayment and monthly payments

The PV for both options (including the down payments) is the same, $8000. What additional factors should terry consider when deciding which aid the best deal for her?

  Determine the rate of discharge at a point

A pipeline 900 ft long discharges freely at a point 200 ft lower than the water surface at intake. The pipe intake projects into the reservoir. The first 600 ft is of 10-in diameter, and the remaining 300 ft is of 6-in diameter.

  Prepare and tabulate the design aid for partial flow

Prepare and tabulate the design aid for partial flow as per the equations for interpolation of velocity and diameter for corresponding flows.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd