Determine the angle of twist of end a with respect to b

Assignment Help Civil Engineering
Reference no: EM13304841

The 800 mm diameter shaft is made of A-36 steel. If it is subjected to the uniform distributed torque of 5kN*m/m, determine the angle of twist of end A with respect to B.

Reference no: EM13304841

Questions Cloud

What was the dollar amount of retained earnings : If the firm follows a residual dividend policy and has no other projects, what is its expected dividend payout ratio?
What is the final temperature of the ice/ water mixture : an insulated beaker with neligiblr mass contains.280kg of liqid water at a temperature of 84.5degree celicous. what is the final temperature of the ice/ water mixture
What is the total power emitted by the sun : The intensity of sunlight at the top of the Earth's atmosphere is about 1360W/m^2. What is the total power emitted by the Sun
Calculate the inflation adjustment for a 5-year loan : You have been assigned to estimate the interest rates that your company may have to pay when borrowing money in the near future. The following information is available.
Determine the angle of twist of end a with respect to b : The 800 mm diameter shaft is made of A-36 steel. If it is subjected to the uniform distributed torque of 5kN*m/m, determine the angle of twist of end A with respect to B.
What s the entropy change of water the is now steam : In a pan on a stove 125 g of water at 100 degrees Celsius is converted to steam. What s the entropy change of water the is now steam
What should be design criteria for water treatment system : The floor area of each floor in these buildings is 400 m^2. The buildings are separated by large lawns so that the (Exposure + Communication) factor = 1.2.
What must be the coupon rate on the bond : Large Industries bonds sell for $1,065.15. The bond life is 9 years, and the yield to maturity is 7%. what must be the coupon rate on the bond?
Determine the wavelength of the photons : A positron emission tomography (PET) scanner examines the gamma rays emitted when positrons and electrons annihilate each other. What is the wavelength of the photons

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the ntu values for each sampling port depth

The packed tower was 30 cm in diameter with sampling ports located at packing depths of 0,2,4,6,8,10, and 12 meters. The loading of water to the tower was 0.039 m^3/(m^2/s), and the temperature of groundwater was 10 degrees celcius.

  Draw the bending moment and shear force diagrams

Draw the Bending Moment and Shear Force diagrams for the girder and calculate the maximum tension in the cable.

  What is the probability that the paper has either a 3 or a 6

suppose there are 10 pieces of paper in a hat. Each piece of paper has a digit 1 through 10 written on it. Each number is written only once. You reach in the hat and select a piece of paper. What is the probability that the paper has either a 3 or..

  Determine normal depth and froude number a pvc pipe

A PVC pipe with a diameter of 30 inches will carry a flow of 20 cfs. the bottom slope is 0.005 and the roughness coefficient is 0.015. determine the normal depth, critical depth, velocity and the froude number.

  Inability and green engineering can be integrated

inability and green engineering can be integrated in the four components of materials science and engineering?

  Find out the number of turns in each spring

Find out the number of turns in each spring, if the diameter of the spring wire 14 mm and the diameter of coil is 80 mm. Assume C=84 GN/mmxmm.

  Design a rectangular reinforced concrete beam for the span

design a rectangular reinforced concrete beam (tension steel only) for the span and superimposed service loads shown. use f'c=5000psi and A615 grade 60 steel. LL=3.5 k/ft over the first 12 feet of the beam

  Heat exchanger second-law efficiency

The condenser in a refrigerator receives R-134a at 700 kPa and 50C, and it exits as saturated liquid at 25 C, The flow rate is 0.1 kg/s,and the condenser has air in at an ambient temperature of 15 C and leaving at 35 C. Find the minimum flow rate ..

  Determine what minimum diameter piston is required

A hydraulic cylinder must produce a minimum force of 3 kN for a pressure of 800 kPa. What minimum diameter piston is required

  Find dry unit weight of the sample and water content

An undisturbed soil sample was collected in a sampling tube of internal diameter 5cm. The length of the extracted sample was 10.2 cm and its mass was 360 g. After oven drying the mass reduced to 326.5 g.

  Find contact time would be reuired for inactivating giardia

How much contact time would be reuired for inactivating Giardia cysts using the following chemicals at the concentrations and temperatures stated: a. Chlorine Dioxide, 23C, 1.0 mg/L b. Chlorine, 12C, 1.6 mg/L c. Ozone, 10C, 5 mg/L d. Chloramines, ..

  What average force was exerted on the ball

After falling from rest from a height of 32 m, a 0.45 kg ball rebounds upward, reaching a height of 22 m. If the contact between ball and ground lasted 1.5 ms, what average force was exerted on the ball?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd