Determine the aeration period and f by m ratio

Assignment Help Civil Engineering
Reference no: EM13310407

Two activated sludge aeration tanks in Podunk, MO are operated in series. Each tank has the follwing dimensions: 7.0 m wide x 28.0 m long x 3.5 m effective liquid depth. The plant operating parameters are:

Flow = 0.0945 m^3/s MLVSS = 1650 mg/L

BOD5 after pimary settling = 135 mg/L MLSS = 1.35 (MLVSS)

Determine the aeration period and F/M ratio for these operating conditions.

Reference no: EM13310407

Questions Cloud

Create a work breakdown structure code for each task : Use at least one (1) quality resource in this assignment. Note: Wikipedia and similar Websites do not qualify as quality resources.
What is the maimum speed of the ejected electrons : when a photoelectric surface is illuminated with f 437 nm , the stopping potential 1.67 v, what is the maimum speed of the ejected electrons
What is the bright fringe separation : a double-slit arrangment prduce bright interference fringrs that are seprated by 2.60 mm when the wavelengt is 589nm. what is the bright fringe separation
Units of elephants produced sold for $2,000 per unit and the : Country A produces two goods, elephants and saddles. In the year 2006, the 10 units of elephants produced sold for $2,000 per unit and the 25 units of saddles produced sold for $200 per unit.
Determine the aeration period and f by m ratio : Two activated sludge aeration tanks in Podunk, MO are operated in series. Each tank has the follwing dimensions: 7.0 m wide x 28.0 m long x 3.5 m effective liquid depth.
Estimate the bending moment at the base of the chimney : A cylindrical chimney,1 m in diameter and 2.5 m tall is exosed to a uniform 50km/hr wind at standard atmospheric conditions.End effects and gusts may be neglected.
Find is the electron jumping to higher or lower level : an electron in a hydrogen makes a transition between levels and emits a photon with a frequency of 6.91*10^14 hz . find is the electron jumping to higher or lower level
Set up the problem and constraints using algebraic symbols : Two factories are manufacturing and supplying a single type of good to four warehouses. The factories can produce a1, and a2 units of the good each month, and the warehouses need b1, b2, b3, and b4 units each month
Merit system principles and prohibited personnel practices : Merit system principles and prohibited personnel practices are actually fairly complicated to understand and far from obvious in their logical restrictions. Depending on one's government affiliation either as a local, or federal worker, there are a v..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Compute the normal flow rate through the channel

A large drainage channel has a trapezoidal cross section with a bottom width of 75 feet and bank side slopes of 4:1 (H:V). If the normal depth of flow is 25 feet, compute the normal flow rate through the channel (Q in cfs).

  Evaluate the pressure head at point

Evaluate the pressure head at point a and determine the vertical effective stress at point b and evaluate the lateral pressurein the brown clay

  What is the engine speed in revolutions per minute

The air density is 0.00206 slugs/cuft. The car has frontal area of 19.8 sqft, a drag coefficient of 0.28, a wheel radius of 12.6 inches, a drive axle slippage of 3%, and a drivetrain efficiency of 88%.

  What is the greatest bending moment and where is it located

A cantilever beam of length 50 ft is embedded in a wall at A and has a free end B. A concentrated load of 100 kips upward is located at x = 25 ft from A. A uniformly distributed load of 20 kips/ft downward extends from 25 to 50 ft.

  Find what is the constant dollar amount of the payment

You have a $1,500 monthly loan payment. If inflation is 3.5% annually (compounded monthly). What is the constant dollar amount of this payment in your 80th month

  Calculate the elavations at vpc-vpt-high point and station

A 2000 ft vertical curve connects to a +3% grade to a -5% grade. If the vertical tangents intersect at station 52+60.55 and elevation 877.62 ft, calculate the elavations at the VPC, VPT, high point and station 54+00.

  Determine magnitude and location of resultant force acting

The tank contains water to depth of 2m and oil (SG=0.8) on top of the water to a depth of 1m. Determine the magnitude and location of the resultant force acting on one end of the tank (i.e. 3m high by 3m wide).

  How many feet below railway should curve pvi be located

An existing high-way railway at-grade crossing is being redesigned as a grade seperated to improve traffic operations. the railway must remain at the same elevation. the highway is being reconstructed to travel under the railway.

  Explain why would it be dangerous to use the material

A structural component in the form of a very wide plate is to be fabricated from 4340 steel that was cooled using a fast cooling rate and has a yield strength of 1515 MPa and a fracture toughness (KIC) of 60.4MPam.

  Find the tension in the cord when the radius is given

The ball is kicked so that it has a velocity of 0.5 m/s and the cord is pulled in at a rate of 0.2 m/s. Neglect friction so that the only important force on the ball is the tension in the cord. Find the tension in the cord when the radius is 0.25 ..

  Does the subject driver have enough time to read the sign

The letter size is such that the sign can be ready by a person with 20/20 vision from a distance of 200 ft. Does the subject driver have enough time to read the sign at a speed of 30 mi/h

  Which route is attractive by using total investment analysis

The state highway department is considering six routes for a new highway. Listed below are the estimated construction costs, maintenance costs, and the user cost associated with each route.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd