Determine spcs83 coordinates of stations b and c

Assignment Help Civil Engineering
Reference no: EM131143620

If station A has SPCS83 state plane coordinates E = 634,728.082 m and N = 384,245.908 m, balance the departures and latitudes computed in Problem 20.30 using the compass rule, and determine SPCS83 coordinates of stations B and C.

Problem 20.30:

Using grid lengths of Problem 20.28 and grid azimuths from Problem 20.29, calculate departures and latitudes, linear misclosure, and relative precision for the traverse.

Problem 20.28:

Assuming a scale factor for the traverse of Problem 20.27 to be 0.99996294, calculate grid lengths for the traverse lines.

Problem 20.27:

The horizontal ground lengths of a three-sided closed-polygon traverse were measured in feet as follows: AB = 501.92, BC = 336.03, and CA = 317.88 ft. If the average orthometric height of the area is 4156.08 ft and the average geoid separation is -23.05 m, calculate ellipsoid lengths of the lines suitable for use in computing SPCS83 coordinates. (Use 6,371,000 m for an average radius for the Eart.

Problem 20.29:

For the traverse of Problem 20.27, the grid azimuth of a line from A to a nearby azimuth mark was 10°07'59" and the clockwise angle measured at A from the azimuth mark to B, 213°32'06". The measured interior angles were A = 41°12'26", B = 38°32'50" and C = 100°14'53". Balance the angles and compute grid azimuths for the traverse lines. (Note: Line BC bears easterly.)

Problem 20.27:

The horizontal ground lengths of a three-sided closed-polygon traverse were measured in feet as follows: AB = 501.92, BC = 336.03, and CA = 317.88 ft. If the average orthometric height of the area is 4156.08 ft and the average geoid separation is -23.05 m, calculate ellipsoid lengths of the lines suitable for use in computing SPCS83 coordinates. (Use 6,371,000 m for an average radius for the Earth.)

Reference no: EM131143620

Questions Cloud

Create an entity diagram showing all your attributes : Create an entity/relationship diagram (ERD) showing all your entities, attributes, and relationships. Sketch your ERD by hand or use a drawing program. Your diagram must beon a single page.
Calculate grid lengths for the traverse lines : The horizontal ground lengths of a three-sided closed-polygon traverse were measured in feet as follows: AB = 501.92, BC = 336.03, and CA = 317.88 ft. If the average orthometric height of the area is 4156.08 ft and the average geoid separation is ..
What is the standard deviation of the returns on this stock : The returns on the common stock of Maynard Cosmetic Specialties are quite cyclical. In a boom economy, the stock is expected to return 22 percent in comparison to 9 percent in a normal economy and a negative 14 percent in a recessionary period. The p..
Lehman company acquired equipment costing : At the beginning of 2008, Lehman Company acquired equipment costing $90,000. It was estimated that this equipment would have a useful life of 6 years and a residual value of $9,000 at that time.
Determine spcs83 coordinates of stations b and c : Using grid lengths of Problem 20.28 and grid azimuths from Problem 20.29, calculate departures and latitudes, linear misclosure, and relative precision for the traverse.
How can we convey professional attitude in our communication : Being in a position of leadership is synonomous with maintaining a "professional attitude." - How can we convey a professional attitude in our communications?
What is the expected return on the portfolio : You own a portfolio that has $20,000 invested in Albuquerque Mining and $14,000 invested in Oklahoma City Drilling. The expected returns on these stocks are 12.5 percent and 9 percent, respectively. What is the expected return on the portfolio?
Does this company have a published code of ethics : Why do you consider this to be an ethical company or not? Provide specific references to support your position. Consider the following questions in your conclusion. In what ways does a company's ethics (good or bad) influence your buying decisions..
What is the expected rate of return on this stock : The common stock of Lester Lithographic is expected to earn 9 percent in a recession, 7 percent in a normal economy, and lose 2 percent in a booming economy. The probability of a boom is 5 percent while the probability of a recession is 50 percent. W..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Discuss the development and distribution of mechanical

If the outer fibers of the shaft yield plastically over a depth of 1/4 of the diameter during the application of the bending moment, qualitatively discuss the development and distribution of mechanical residual stresses along the diameter of the s..

  Design method to select the most economical beam section

A simply supported steel beam carries a factored concentrated load of 25 kips at the center of its 36-ft span. The beam has lateral support at the center of the span and at both ends (Lb = 18 ft). Use the AISC design

  Determine total time for the compression wave to travel down

You are to perform a dynamic pile load test on a24-inch OD open ended homogeneous pipe pile. The pile has a shellthickness of 0.5 inch and is 80 feet long. Calculate: Compression wave velocity(hint: E=29x106 psi, g=490 pcf)

  Does the ph of beverage remain the same or increase

When you allow a can of carbonated beverage to sit open so that the carbon dioxide is released to the air, does the pH of beverage remain the same, increase, or decrease Why

  Find specific weight and total moisture content of sample

A sample of dry sand with a specific gravity total of 16.49 kN/m3 and a relative density of 2.67 grains, is placed outdoors. During a rainy period, the sample volume remains constant but the degree of saturation increases to 40%.

  Calculate value of temperature that can increase efficiency

An engineering student, recognizing that the "ideal gas law" requires gas velocity to be function of temperature, suggests that an easy way to increase efficiency would be to change the temperature of the exhaust gas being treated.

  Calculation of nodal displacement vector

Analyse the bar using the Galerkin finite element method. The coding solution for linear h-refinement and its manual solution for a limited number of linear elements areon Blackboard for your reference.

  Find the value of y at x =21

State Newton - Gregory forward difference interpolation formula 16. Find the value of Y at x =21

  Determine the magnitude of theacceleration at the instant

A car travels along a horizontal circular curved road that has aradius of 600 m. If the speed is uniformly increased at a rate of2000 km/ h2 , determine the magnitude of theacceleration at the instant the speed of the car is 60 km/h.

  Define what is meant by the term compile-time binding

Define what is meant by the term compile-time binding and list two other terms that are also used to describe it. Explain why compile-time binding can present problems when implementing polymorphism in a program.

  How many cubic yards of aggregate must be ordered

how many cubic yards of aggregate must be ordered for a road base 16 inches thick and 2000 feet long with a top width of 30 ft, if the side slopes are one on one, or 45 degree

  Draw the flow net for the steady state seepage flow

Draw the flow net for the steady state seepage flow which occurs under this wall. From the flow net determine the distribution of water pressure on the side AB of the wall and then find the resultant force (per metre run into the page) exerted by ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd