Determine percentage of truck as seen by stationary observer

Assignment Help Civil Engineering
Reference no: EM13310048

From a photograph one observs that on a level section of highway 20% of the vehicles are trucks, 80% are cars, and that there are 50 vehicles per mile of highway. The trucks travel at 40 mph, the cars at 50 mph. This highway also has a section with a steep grade on which the speed of the trucks drops to 20 mph, and the speed of the cars to 40mph. No vehicles enter or leave the observed sections of the highway (except at the ends), and the flows are stationary. There is no traffic congestion, gueuing or vehicle backup on this highway. Determine the percentage of trucks as seen by a stationary observer on the grade.

Reference no: EM13310048

Questions Cloud

Use the definition for the laplacian in the discrete case : Show that subtracting the Laplacian from an image is proportional to unsharp masking. Use the definition for the Laplacian in the discrete case to derive the equivalence relation, constant weighting factors should not affect your conclusion.
What is the speed of the skater after the ball is thrown : A 55-kg mass ice skater standing stationary on very slipper ice (negligible friction) throws a 0.45 kg baseball with a speed of 27 m/s in the horizonatal direction
Find direction of the velocity of these skaters : Two Skaters collide and hold on to each other on a frictionless floor. find direction of the velocity of these skaters after the collision
Constant speed and constant kinetic energy : When a driver applies the brakes to keep a car going downhill at a constant speed and constant kinetic energy, the potential energy of the car decreases. Where does this energy go? Where does most of it appear in a hybrid vehicle?
Determine percentage of truck as seen by stationary observer : From a photograph one observs that on a level section of highway 20% of the vehicles are trucks, 80% are cars, and that there are 50 vehicles per mile of highway. The trucks travel at 40 mph, the cars at 50 mph.
What is the mass of this piston : A vertical cylindrical tank contains 1.80 mol of an ideal gas under a pressure of 1.00 atm at 20.0oC. What is the mass of this piston
Various administrations private and public : There are four major management theories that have been applied in various administrations; private and public.
Obtain the maximum energy stored in the inductor : If a capacitor has the initial charge of 5.0uC, L = 0.080H, C = 10uF, and R = 0, What is the maximum energy stored in the inductor
Determine the shear-thrust and moment in the arch at point c : The three hinged arch is composed of segments of a circle. Support points A and D are not at the same level.Determine: (a) the horizontal and vertical components of reaction at A and D.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Determine what is the book value at the end of year 3

A hybrid car has a initial cost of $70,000 is to be depreciated by the straight-line method over a six years. The asset will a salvage value of $10,000. According to the straight line method, the book value at the end of year 3 is

  What is the probability of no health hazard in 30 days

Air pollution in a city is caused by the following four sources: vehicle exhaust (V), industrial exhaust (I), dust (D), and pollen from plants and trees (T). On a particular day, the likelihood of air pollution caused by these sources is 4:3:2:1, ..

  Determine the heat transfer rate from the compressor

In a refrigeration system Refrigerant 22 enters the compressor at 150 kPa and -10 C. It leaves the compressor at 1.0 MPa and 90 C. Assume the mass rate of flow through the compressor is 0.016 kg/s

  Determine the speed of the stone

A 0.20 kg stone attached to a 0.8 m long string is rotated in a horizontal plane. The string makes an angle of 25° with the horizontal. Determine the speed of the stone.

  What is capacity of pump required to supply max discharge

What is the capacity of the pump required to supply maximum required discharge to the model, in CFS The length of time the model must be operated to check the equivalent of 36 hours of operation for the prototype operation, in decimal format hours..

  How to calculate the forces in members ec and ef

Using method of joints, calculate the forces in members EC and EF. Note that the length of the member CD is 3.464 m, the length of member EC is 2m, and angle CDE is 30 degree ( this will cut down a bit of trigonometry effort).

  Maximum size of coarse aggregate

What is your recommendation for the maximum size of coarse aggregate for the following situation? A continuously reinforced concrete pavement cross section contains a layer of No. 6 reinforced bars at 15.24 cm centers,

  Compute the bearing pressure at each corner of the footing

that acts at a 45 degree angle from the side of the footing (it acts diagonally across the top of the footing) determine whether the resultant force acts within the kern. If it does, then compute the bearing pressure at each corner of the footing.

  Determine economical number of trucks and direct cost

A project involves transporting iron pipe to a jobsite that is 43 miles from the supplier. The pipe will be hauled in trucks that can carry 16 pipes per load. Each pipe is 20 ft in length. The average haul speed of a truck will be 50 mi./hr and re..

  Determine the largest mass-m which the frame can carry

The frame is desinged to carry the hanging mass at G equal to 167 kg. The frame is supported by a pin connection at C and the rope AB, and constructed with pin connections at points E, F, and D.

  Compute the max acceptable tensile service load for angle

The service live load is three times the dead load. The 4-in leg contains a single line of 7/8 inch diameter bolts, and the 6 inch leg contains a double gage line of 7/8 inch diameter bolts.

  Determine time at which collar starts to slip relative to it

The coefficient of static friction between the collar of mass m=2 kg and the bent bar is Us=0.35, and the collar is initially d=70 cm from the spin axis AB. Assuming the motion starts at t=0, determine the time at which the collar starts to to sli..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd