Determine normal depth and froude number a pvc pipe

Assignment Help Civil Engineering
Reference no: EM13304176

A PVC pipe with a diameter of 30 inches will carry a flow of 20 cfs. the bottom slope is 0.005 and the roughness coefficient is 0.015. determine the normal depth, critical depth, velocity and the froude number.

Reference no: EM13304176

Questions Cloud

Find how much does the student owe at the interest rate : The compound interest formula is F=P(1+i)n where F is the total amount due, P is the initial cost or amount of money, i is the interest rate, and n is the number of periods interest is computed. 1.A student purchases a $1400 laptop computer for sc..
Calculate the volume flow rate in liters per minute : Blood flows in an aorta of radius 8.0 mm at 28 cm/s. Calculate the volume flow rate in liters per minute
What should the diameter of the constricted section be : The pressure in a section of horizontal pipe with a diameter of 2.0 cm is 146 kPa. Water flows through the pipe at 2.80 L/s. what should the diameter of the constricted section be
Would it make sense to sell the company for this amount : The deal structure includes the assumption of a $500.0 bond issue that matures in 2018, with a stated coupon rate of 5.5% and a current yield of 3.45%. It is anticipated the equity issue will be 100.0 shares.
Determine normal depth and froude number a pvc pipe : A PVC pipe with a diameter of 30 inches will carry a flow of 20 cfs. the bottom slope is 0.005 and the roughness coefficient is 0.015. determine the normal depth, critical depth, velocity and the froude number.
Find the new current in the circuit : Five identical resistors, each of resistance R, are connected in series to a battery, and a current of 7.39 A flows in the circuit. Find the new current in the circuit
How does a supermarket use ict : how does a supermarket use ICT to know when to order more stock?
How far does the water have to fall : Water at 20°C exits a circular tap moving straight down with a flow rate of 10.1 cm3/s. If turbulent flows are characterized by Reynolds numbers above 2300 or so, how far does the water have to fall before it becomes turbulent
Discuss the efficient markets hypothesis : Discuss the efficient markets hypothesis and its significance for the theory of finance. Explain why market efficiency leads a manager to focus on NPV and free cash flow.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What bolt sizes must be used for the allowable shear stress

A structural steel beam is attached to a column with bolts. The downward force on the connection is 150 kips. What bolt sizes must be used if the allowable shear stress is 25.0 ksi

  Find the probability of landing on the head side of the coin

A coin is tossed and a single 6-sided die is rolled. Find the probability of landing on the head side of the coin and rolling a 3 on the die.

  Calculate the factor of safety and deformation

A 1 cm diameter, 0.4 m long steel rod is to be used in an application where it will be subjected to an axial tensile force of 15kN. The factor of safety based on yield stress must be at least 1.5, and the axial deformation must not exceed 2 cm.

  Calculate efficiency of esp required to meet federal source

A coal with 6% ash and a heating value of 13,000 Btu/lb is burned in a new power plant. Assume that 30% of the ask falls out as bottom ash in the furnace. Calculate the efficiency of ESP required to meet federal new source performance standards.

  Determine the station where tangent runout starts

The station of a PI of a horizental curve is 60+20. The horizental curve has a degree of 4 and a length of 400ft. the othere given design perameters include. Superelevation runoff rate is 1/400. width of the pavement is is 15ft.

  Determine the stations and elevations of pvcs and pvis

Using a design speed of 50 mi/h, determine the stations and elevations of PVCs, PVIs, and PVTs of the two vertical curves required to connect the highway segments, as well as the length of the constant grade section (connecting grade is to be as s..

  What is the engine speed in revolutions per minute

The air density is 0.00206 slugs/cuft. The car has frontal area of 19.8 sqft, a drag coefficient of 0.28, a wheel radius of 12.6 inches, a drive axle slippage of 3%, and a drivetrain efficiency of 88%.

  Determine the cod

Determine the COD, carbonaceous BOD, and nitrogenous oxygen demand of a 100 mg/L solution of urea (N2H4CO)

  Determining the amount of investment

If they plan to increase their savings by 5% each year, how much must they invest in the first year given that they expect to earn 4% per year on their investment?

  Estimate the daily emissions of sulfur dioxide

Estimate the daily emissions of sulfur dioxide, nitrogen oxides as NO2, and particulate matter from an industrial steam-generating plant equipped with a dry-bottom pulvurized-coal firing system.

  What are the additional treatment processes required and why

Discuss the role of each physical, chemical and biological unit operations and processes employed in the wastewater treatment facility. If this treatment facility is required to supply class A recycle water to those industries for non-potable use

  What are the concentrations of the reactants and products

If 0.100 mol each of SO2 and NO2 are placed in a 500 mL vessel at this temperature, what are the concentrations of the reactants and products when equilibrium is established for this reaction?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd