Determine how many years from now the consumption will reach

Assignment Help Civil Engineering
Reference no: EM13562641

A community has a current population of 15,000. 10 years ago, the population was 12,500 and the community has a declining growth rate with a saturation population of 22,000. The total water consumption for the community at present is 2.25 million gallons per day. The treatment plant has a capacity of 0.3 million gallons per day. Determine how many years from now the consumption will reach 85% of its design capacity if current water usage rates remain steady

Reference no: EM13562641

Questions Cloud

Determine the weight of the satellite in pounds when it : A satellite would have a mass of 200 kg on the surface of the moon. Determine the weight of the satellite in pounds when it is in orbit 10,000 mi. above the surface of the earth.
Determine how fast does the spot of laser light sweep : A turntable that turns 10 revolutions each second is locatedon top of a mountain. how fast does the spot of laser light sweep across cloudsthat are twice as far away
Determine the concentration of ubod in the effluent : If the length of the river connection between the two lakes is equal to 3km and the velocity in the river is equal to 0.4 m/s, determine the concentration of UBOD in the effluent from the second lake.
Calculate the angles most probable value : An angle is observed repeatedly using the same equipment and procedures. Calculate a) the angle's most probable value, b) the standard deviation, and c) the standard devaition of the mean
Determine how many years from now the consumption will reach : A community has a current population of 15,000. 10 years ago, the population was 12,500 and the community has a declining growth rate with a saturation population of 22,000. The total water consumption for the community at present is 2.25 million gal..
Graph the pressure and piezometric head in the tank as : Water flowing through 80 feet of 4-inch-diameter average cast iron pipe (ks=0.00085 feet) causes a friction head loss of 0.27 feet. Find the flow rate. Assuming viscosity v=1.079*10^-5 ft^2/s
Find at what speed is this galaxy reading from earth : The spectral lines of various elements are detected from agalaxy in constellation ursa major. At what speed is this galaxy reading from earth
Find an expression for the diameter : A drop of water forms under a solid surface. assume the drop has the shape of a hemisphere just before seperating. find an expression for the diameter, D, of the droplet, in terms of the specific weight and surface tension, assuming the contact angle..
What size is the smallest detail that can be resolved : A 1.2 MHz ultrasonic beam is used to scan body tissue. If the speed of sound in a certain tissue is 1540 m/s, what size is the smallest detail that can be resolved

Reviews

Write a Review

Civil Engineering Questions & Answers

  The principal strains and the maximum engineering

The engineering strains at a point on a building frame weredetermined by means of FEM as

  How could it be that a beam that weighs only 5 grams

The actual weight of the Rectangular Aluminum Beam (used in Task 3) is 25 grams, while the actual weight of the Square Aluminum Box Beam is only 5 grams.

  What rate of return did the company make on the process

Barron Chemical uses a thermoplastic polymer to enhance the appearance of certain RV panels. The initial cost of one process was $130,000 with annual costs of $49,000 and revenues of $78,000 in year 1, increasing by $1000 per year.

  Three cylinders from the same mix were tested

Three cylinders from the same mix were tested for strenght.  Cylinders A and B were cast in 4x8 molds while cylinder C was cast in a 6x12 mold.  The total loads were as follows; cylinder A= 65,200 lbs.,  cylinder B= 68,550 lbs., cylinder C= 151,190 l..

  Calculate consolidation settlement 3 years after placement

The investigation results indicated that the clay had a saturated density of 1.6 Mg/m3, an average initial void ratio of 1.8 and the preconsolidation pressure at the mid depth of the clay layer was 20 kPa.

  Shape of a circular arc

Rod AB is bent into the shape of a circular arc and is lodged between two pegs D and E. It supports a load P at end B. Neglecting friction and the weight of the rod, determine the distance c corresponding to equilibrium when a = 43mm and R = 143mm..

  What should be the surface area-m2 of each tank

If a 1.0 m3/s flow water treatment plant uses 10 sedimentation basins with an overflow rate of 15 m3/day.m2, a-what should be the surface area (m2) of each tank?( i got this part right the answer is 567 m2)

  Compute the geodetic coordinates of the station qbn from

Compute the geodetic coordinates of the station QBN from station MDU If coordinates of station MDU are f = 39°51'55"N, ? = 104°40'58"W Distance = 30km, Az = 243°40'48”, h = 1850m, dh= -20. Ellipsoid GRS80

  Find the moment of inertia around the x-axis and y-axis

Using a unit analysis, calculate the value of the K term in the rational method equation (Q = K C I A) in English and SI respectively.

  Determine the components of the reaction at point c

The object ABC consists of two slender rods welded together at point B. Rod AB has a mass of 1 kg and bar BC has a mass of 2 kg. Knowing the magnitude of the angular velocity of ABC is 10 rad/s when thetha is zero.

  Calculate the bulk density and water content of peat ratio

A 150 mm diameter by 300 mm long sample taken from the peat deposit was weighed and found to have a total mass of 5036 g and after oven-drying a dry mass of 387,4 g.

  Write a report on toxic and hazardous waste

Toxic and Hazardous waste: how are they treated, safety measures, regulations in USA about hazardous waste.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd