Determine e at an arbitrary point along the y axis

Assignment Help Electrical Engineering
Reference no: EM13285960

there are two infinite lines, each carrying uniform charge density ? and they reside in free space located parralel to the z axis at x = -1 and

x =1. determine E at an arbitrary point along the y axis.

Reference no: EM13285960

Questions Cloud

Calculate the volume of the bubble : An air bubble has a volume of 1.25 cm3 when it is released by a submarine 100 m below the surface of a lake. What is the volume of the bubble when it reaches the surface
Find out the expression for the rate of reaction : Determine the expression for the rate of reaction with respect to each of the reactants and products.
How many atoms are there in earth : Earth has a mass of 5.98 × 1024 kg. The average mass of the atoms that make up Earth is 40 u. How many atoms are there in Earth
Describe what is the final temperature : If energy obtained from burning 1.23 pounds of butane (feul value is 10.85 kcal/g) is used to heat 126.5 kg of water at an initial temperature of 20.7 degrees C, what is the final temperature
Determine e at an arbitrary point along the y axis : there are two infinite lines, each carrying uniform charge density  and they reside in free space located parralel to the z axis at x = -1 and x =1. determine E at an arbitrary point along the y axis.
What is the approximate return for this investment : Assume a project that has the following returns for years 1-5: 15%, 4%, -13%, 34%, and 17%. what is the approximate return for this investment?
Define two pieces of zinc as electrodes : A concentration cell is built based on the following half reaction by using two pieces of zinc as electrodes (each weighing 100.0 g), two Zn2+ solutions
Find the direction of total electric force exerted on charge : Four identical charged particles (q= +10.0µC) are located on the corners of a rectangle. find the direction of the total electric force exerted on the charge at the lower left corner by the other 3 charges
Design a 3-bit 4-1 mux using discrete logic gates : The 4 sources are I0 I1 I2 I3 and the output is Y (note that these are all 3-bit words). Individual bits of I0 are I0(0), I0(1), and I0(2); individual bits of I1 are I1(0), I1(1), and I1(2); and so on. The select signals are s1 s0 (s1 is the msb a..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the power factor of the load and the line current

An idustrial plant uses two pieces of equipment. A) A lightining element that comsumes 10 kw when supplied at 100v, 60Hz; and B) A furnance consuming 360 kw and 400 KVAR when supplied at 2000v, 60Hz.

  Calculate the leading kvars the syncrhonous motor

A 277/480V three phase wye system has the following load: M1- Induction Motor, 50hp, n=0.91, PF= 0.89 at full load. M2- Induction motor, 25hp, n=0.9, PF= 0.9 at full load. R- Heater Load, PF=1 M- A synchronous motor to drive a second 25hp load.

  What is the transformer efficiency for the output voltage

A 10 kVA 1100:120 V single phase transformer has the following circuit parameters referred to the primary. Rc = 80 k Ohm, Xm = 10 k Ohm, Re = 20 Ohm, Xe = 50 Ohm. If the secondary load impedance is 5

  How large is the correlation coefficient for gsm 900 system

Assuming that directions of arrival are uniformly distributed at the mobile, how large is the correlation coefficient for a GSM 900 system between the channel in the middle and the end of the burst when the mobile station moves at 200 km/h

  Design a bias-stable common emiter amplifier circuit

design a bias-stable common emiter amplifier circuit whose output is capacitively coupled to a load resistor RL = 10KΩ using a 20V power supply. The Minimum small signal voltage gain should be -20V/V. Assume the following parameters for the transi..

  Determine the awg size of the extension cord

The resistance per 304.8 m of copper wire uses in the extension cord of AWG 14,12,10,8 and 6 are 2.58,1.62, 1.02, 0.64 and 0.41 respectively. Assume a 2% allowable voltage drop. Show all working .

  Find the inductance l and capacitance c of the circuit

The bandwith of a series resonant circuit is 400 Hz. if the resonant frequency is 4000 Hz, find Q. and if R = 10 ohms, what is the value of XL at resonance", and Find the inductance L, and capacitance C of the circuit

  Determine the bit error rate performance

A signal is modulated by BPSK and transmitted over an AWGN channel. At the receiver, the bit error rate performance is 0.001

  Show that the system has no overshoot in the step response

A causal LTI dicrete time system is said to have an overshoot in its step response if the response exhibits an oscillatory behavior with decaying amplitude around a final constant value.

  Calculate r-l and the inductor current i

The instantaneous power p into a one port containing resistors and inductors has maximum value 100(1+sqrt2) W and minimum value 100(1-sqrt2)W. (note that instantaneous power is measured in W, and it contains various contributions

  Determine the steady state error for a unit step input

(a) Determine the steady state error for a unit step input R(s) = 1 / s. (b) Assume that the complex poles dominate, and determine the overshoot and settling time to within 2% of the final value.

  State the phase relationships between each pair of the phase

Suppose that V1 (t)=100cos(ωt) and V2 (t)= 100sin(ωt). Use phasors to reduce the sum Vs (t)=V1 (t)+V2(t) to a single term of the form Vm cos(ωt+θ). Draw a phasor diagram, showing V1, V2 ,and Vs. State the phase relationships between each pair of t..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd