Determine draft when the barge is empty of all corn and rain

Assignment Help Civil Engineering
Reference no: EM13302732

A barge measures 10 ft (depth) by 35 ft by 120 ft and weighs 100 U.S. tons. The barge floats in fresh water (specific weight = 62.4 lb/ft3) and is evenly filled with 38,000 bushels of corn (60 lb/bushel). Express final answers to two decimal places:

a) Determine the draft (feet) of the barge full of corn.

b) How many inches of rain can fall over the entire barge full of corn before it begins to sink?

c) Determine the draft (inches) when the barge is empty of all corn and rain.

Reference no: EM13302732

Questions Cloud

What is the thermal efficiency of this heat engine : A heat engine using a diatomic ideal gas goes through the following closed cycle, What is the thermal efficiency of this heat engine
Calculate the projects annual project free cash flow : Calculate the projects annual project free cash flow (PFCF) for each of the next five years where the firms tax rate is 35%.
Develop an entity-relationship diagram as a conceptual mode : For the following requirements analysis description, develop an Entity-Relationship Diagram as a conceptual model that captures all of the requirements to the fullest extent possible.
Determine the maximum allowable tensile force : An aluminum link is subjected to axial tension. The loading is limited by the conditions of not yielding and not elongating excessively. The yield limit is satisfied if the stress remains below 50%of the 325M Payield stress.
Determine draft when the barge is empty of all corn and rain : A barge measures 10 ft (depth) by 35 ft by 120 ft and weighs 100 U.S. tons. The barge floats in fresh water (specific weight = 62.4 lb/ft3) and is evenly filled with 38,000 bushels of corn (60 lb/bushel).
How much less will the real world have to charge : If Judy increases the number of required exposures for Women > 55 by 10 will she need to rerun the model?
State fault tolerance approaches that systems managers use : Windows server software works seamlessly with most hardware vendors that offer fault tolerant systems. Discuss fault tolerance approaches that systems managers use to assure continuity of operations.
Determine how far did the train travel during the time : A train moving at 100 km/hr decreases its speed to 80 km/hr in 3.5 seconds. How far, in meters, did the train travel during this time
What is its total corporate value : The company owns marketable securities of $100 million. It is financed with $200 million of debt, $50 million of preferred stock, and $210 million of book equity.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the order and class of the leveling

Differntial Leveling between BM's A,B,C,D, and A gives elevation differences (in meters) of -15.632, 32.458, 38.214, and -55.025, and distances in km of 4.0, 6.0, 5.0, and 3.0 respectively.

  Determine the maximum shear stress at the end

A 600 mm long solid steel shaft is to transmit a torque of 30 N-m, G=90 GPa, diameter 15mm. Determine (a) Maximum shear stress, and (b) Angle of twist (phi) at the end.

  What is the stress along the top edge and the bottom edge

A horizontal pre-stressing force of 500kN is applied to rectangler beam. the beam has a depth of 500mm and a width of 250mm. the force is applied at a distance of 80mm below the x-x axis.

  Find void ratio and wet unit weight for degree of saturation

A sand sample has a porosity of 38% and specific gravity of solids of 2.66. Find the void ratio and wet unit weight in lb / ft3 if the degree of saturation is 35%.

  Tightening of bolt in the friction grip

What difference does the tightening of bolt in the friction grip joint make to the load at first slip and the failure load.

  What is the concentration of ocl-

HOCL is added to water in a tank as a disinfectant. after equilibrium is reached it is found that the pH of the water in the tank is 8.2 and the gas phase partial pressure is the head space of the tank is 0.2E-7 atm. (not: henry's law constant for..

  What is the corresponding horizontal distance

A runs slope a distance of 156.777 m from one point to another point at a rate of +1.5%. What is the corresponding horizontal distance between the points?

  Determine what is the lattice of the structure

A particular unit cell is cubic with ions of type A located at the corners and facecenters of the unit cell and ions of type B located at the midpoint of each edge of the cube and at the body centered position.

  Shear tension and bending of the fixed i-beam

To satisfy desige limitation it is necessary to determine the effect of the 2- kN tension in the cable on the shear tension and bending of the fixed I-beam.

  Find the pressure required to fill container at both point

find the pressure required to fill the container when the height of the fluid is h = 0.75m at both point 1 (intake 1) and 2 (intake 2). Assume the air is at atmospheric pressure until the water level passes intake 2 (at h = 0.5m) and the air follo..

  Determine the maximum altitude reached by the rocket

A powered model rocket is launched in the vertical direction. The altitude of the rocket is 100FT (above ground level) at the end of the powered portion of the flight. The rocket lands 19.676 seconds from the powered portion of the flight.

  Calculate stress along edge a-b caused by prestressing force

A horizontal pre-stressing force of 750kn is applied to a rectangular concrete beam to be used as a structural member of a traffic bridge. The beam has a depth of 500mm and a width of 250mm. The force is applied at a distance of 80mm below the sec..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd