Design a simply supported one-way reinforced concrete floor slab to span 10 ft and carry a service live load of 175 psf and a service dead load of 25 psf. Use fc' = 3000 psi and fy = 60,000 psi. Make the slab thickness to ½-in. increments. Unit weight of concrete=150 lb/ft3

a) Design the slab for the ACI Code minimum thickness.

b) Design the thinnest possible slab allowed by the ACI Code.

Calculate the kinetic energies of two uniform solid cylinder : Calculate the kinetic energies of two uniform solid cylinders, each rotating about its central axis. They have the same mass, 2.75 kg |

Why would a slant medium containing only dextrose : Instead of TSI, why would a slant medium containing only dextrose and lactose (not sucrose) be preferable for detecting Y. enterocolitica? |

State the structure of the product that is formed : Draw the structure of the product that is formed when 1-pentyne undergoes reaction with two equivalents of HCl. |

A recession in the united states is likely to raise the grow : A recession in the United States is likely to raise the growth of real GDP in Europe. Do you agree or disagree? Why? (This assignment must be 250-300 words and include at least 2 cited references in APA 6th edition format). |

Design the thinnest possible slab allowed by the aci code : Design a simply supported one-way reinforced concrete floor slab to span 10 ft and carry a service live load of 175 psf and a service dead load of 25 psf. Use fc' = 3000 psi and fy = 60,000 psi. Make the slab thickness to ½-in. increments. |

How much gravitational potential energy does she gain : An 80 kg person climbs a set of stairs that are 5 meters high. How much gravitational potential energy does she gain |

Explain the physical and chemical properties of a compound : Are the physical and chemical properties of a compound necessarily similar to those of the elements of which it is composed |

What is the minimum cash balance : A firm has an ending cash balance of $1,700 and a cumulative surplus of $1,300. What is the minimum cash balance? |

How can a firm utilize leveraging to maintain a high level : How can a firm utilize leveraging to maintain a high level of competition? (This assignment must be 250-300 words and include at least 2 cited references in APA 6th edition format). |

## Determine the maximum and minimum stress intensitiesDetermine the maximum and minimum stress intensities in the section. |

## Which truck will cause more pavement damagea 6 inch soil cement base and an 8 inch crushed stone subbase, which truck will cause more pavement damage?(assume drainage coefficients are 1.0) |

## What is the elevation of lower pointA pre- engineering base line was run down a very steep hill.rather than measure horizontaily down hill with steel tape: surveyor measured the vertical angle with the theodolite and slope distance with 16m steel tape. |

## Calculate the largest tolerable internal crack lengthCalculate the largest tolerable internal crack length for a 7075-T651 aluminum alloy component that is loaded to a stress one-half of its yield strength without catastrophic fracture. For the alloy, the plane strain fracture toughness is 24 and yi.. |

## Find the density of air and weight of the air in the tankAn empty air tank has a volume of 0.024 m3. The compressor on the tank is run until the pressure gauge reads about 65 psi (or 22,500 Pa). Assuming the temperature of the tank is 25 C, find the density of the air and the weight of the air in the ta.. |

## What will be the new level of serviceIf an additional 11ft lane is added (each direction) and all other factors stay the same, what will be the new level of service? |

## Rankine cycle and thermal efficiencyDetermine the rate at which heat is added in the boiler, the power required to operate the pumps, the net power produced by the cycle, and the thermal efficiency. |

## Determine what is the design speed of the curveAn equal tangent vertical curve connects a -2% and a +3% grade. The low point of the curve is at elevation 297.88 ft. If the PVI is at elevation 295 ft, what is the design speed of the curve |

## Determining the pressure head at the nozzle inletWater flows steadily through a horizontal nozzle. The nozzle inlet diameter is 6 in. At the nozzle outlet, where the pressure is atmospheric, the diameter is 2 in. Determine the pressure head at the nozzle inlet to produce a water jet velocity of .. |

## Pressure on the soil if theta is givenA pipe is to be installed under the ground on a bed of aggregate 6 in. thick. The entire weight on the aggregate from pipe and soil above the pipe is 1800 lbs. per linear foot of pipe. What is the pressure on the soil if theta is 45 degrees? Assum.. |

## Calculating energy for vacancy formationThe number of vacancies in some hypothetical metal increases by a factor of 4 when the temperature is increased from 1090 K to 1140 K. Calculate the energy (in J/mol) for vacancy formation assuming that the density of the metal remains the same ov.. |

## Determine the coefficient of frictiona mass of 2kilogram is projected with a speed of 3m/s.if a plane inclined 20 degrees with the horizontal.after travelling travelling 0.8meters, the mass comes to rest. determine the coefficient of friction and also the speed as the black returns t.. |

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd