Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
a) Design an operational amplifier cicuit that has the following specifications:
Gain=-3; Input impedence>20 kohm
You have unlimited number of resistors of values 1,2,5, and 10 kohms and LM741 op amps. Input impedance of LM741 op amp is 3Mohm.
b) If the cost of a resistor is 3 cents and LM741 is 50 cents, provide a circuit design with a minimum cost.
1.For an impedance equation, such as 15ohms + j60ohms, explain the steps to determine equivalent series and parallel circuits. 2.For a given parallel RC or RL circuit, explain how admittance, current, and phase would change
What is the principle behind CRT(CATHODE RAY OSCILLOSCOPE), and How this method is simplified in LCD and LED. Is the same CRT principle used in LCD and LED Televisions. If no what is the principle used in LCD and LED Tvs.
An early code used in radio transmission involved using codewords that consist of binary bits and contain the same number of 1s. Thus, the 2-out-of-5 code only transmits blocks of 5 bits in which 2 bits are 1 and the others 0.
A 50 hp, 460 V, three phase induction motor draws 61 amps when operating at rated voltage and at a power factor of 0.85 lagging when supplying a rated load. knowns: 1hp=746watts effeciency (n) = Pout/Pin = Pout/(Pout+losses)
A 345-kV, 3-phase transmission line delivers 100 MVA, 0.866 lagging, to a wye connected load. Calculate the following: a. The total real and reactive power delivered to the load. b. The real and reactive power per phase.
An input signal of 10V at 0degrees and a frequency of 1592Hz is applied to a series RLC circuit with resistor R=100ohm, inductor L= 40mH, and a capacitor C=0.5uF. The value of the total circuit complex impedance is
A bar phantom is imaged by an LSI system which is modeled as an ideal moving average system. The PSF of the system is h(x,y) = rect(x/delta, y/delta) (a) If bar separation of the bar phantom is f what is the output of the imaging system
Important information about Digital signal processing, (a) Design a lowpass FIR digital filter using "remez" routime in Matlab for the following specifications:
The fuel tank contains 33 kWh per gallon. If the vehicle were to be replaced by an electric vehicle that charges from the power grid, how much power would it draw (in W, kW, or MW) to recharge at the same rate as the gasoline powered automobile
a sound distribution system has the following outputs 10 watts at 8ohms,5watts at 4 ohms, 15 watts at 16 ohms and 2 watts at 4 ohms if the input to the amplifier is 20 millivolts at 600 ohms how much gain in decibels will be required of the amplif..
Using MATLAB, plot the pole zero map and the Bode plot of the two transfer functions and paste the graphs below. Identify and briefly discuss the differences between the Bode plot of the two transfer functions.
The internet connection speed at any time from your home can depend on the amount of overall internet trac at that time. Let the random variable X denote the speed of connection in megabits per second (MBPS).
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd