Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Your boss has assigned you the job of designing a rapid-mix tank for the new water treatment plant for the town of Waffle. The design flow rate is 0.050 m^3/s. The average water temperature is 8 degrees celcius. The following design assumptions for a rapid-mix tank have been made:
1. number of tnaks = 1 ( with 1 backup)2. tank configuration: circular with liquid depth = 1.0 m3. detention time = 5s4. velocity gradient = 750 s^-15. impeller type: turbine, 6 flat blades, Np = 3.66. available impeller diameters: 0.25, 0.50, 1.0m7. assume B = (1/3)H
Design the rapid-mix system by providing the following:1. water power input in KW2. Tank diameters in m3. Diameter of the impeller in m4. Rotational speed of impeller in rpm
If the allowable shear stress in the 7/8" diameter bolt is 35 ksi, determine the allowable force F that may be applied.
Two immiscible fluids are in contact. Fluid I is denser and is also well mixed. The concentration of species a is cao everywhere within this fluid and the temperature in fluid I is held constant at To.
An open clean glass tube, having a diameter of 3 mm is inserted vertically into a dish of mercury at 20c .How far will the column of mercury (S.G =13.6) in the tube be depressed in (mm) given the following information. Theta = 130 and surface tens..
The rod has a uniform cross-section of 53mm2. The external load consists of point loads: two P1 of 3kN, two P2 of 1kN, and one P3 of 7kN. What is the normal stress at the fixed support
We are analysing energy efficiency of four different cars, A (3.2 miles/kwh), B (42 mpg using Clean Diesel), C (22 mpg using corn based ethanol E85), and D (28 mpg using regular gasoline). Now accounting for all of the energy used, including extra..
Think of a situation where CAD is a better choice then traditional drafting. Given multiple ways to input coordinates, is one way better than another? Are there situations where you ell use one method over and other?
Calculate the heat transfer per unit mass during the expansion if the exit temperature is 50 degrees celcius.
A. List of all possible resistance combinations that can be formed with these springs. indicate drawings and calculation of each unique configuration. B. How many unique combinations can be formed
A steady fire with an energy release rate of 500 kW occurs in a room 3m wide, 3m long, and 2.4 m high, with a door opening which is 1.8 m high and 0.6m wide. the ambient temperature is 20 degree celcius.
The maximum speed of trains for urban rail transit is 60 mph and maximum acceleration/deceleration rates allowed for standing passengers are 5 feet/sec2. Part A) If the station spacing is determined at 1000 ft, what is the maximum average running s..
Two Tangents intersect at a PI Station of 35+33.24 whose coordinates are N=10349.64 feet and E= 10436.79 feet. The Intersection angle (I) = 20°15'42" Right, and the azimuth of the back Tangent is 23°14'32". (This azimuth is from the PC to the PI.)
A gas is compressed at a constant pressure of 0.800 atm from 9.00L tp 2.00L. in the process, 400J of energy leave the gas by heat. (a) What is the work done on the gas? (b) What is the change in it internal energy?
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd