Design an audio amplifier system

Assignment Help Other Engineering
Reference no: EM131433812

Question: Design an audio amplifier system that will take input signal of 100 mV from a microphone of 75 ?, amplify the signal with a gain of 40, and finally drive a speaker of 8 ?.

You have to perform your simulation in a SPICE simulator (LTSPICE, PSPICE, etc.) and you are allowed to use either BJT or MOSFET to design your system. You must use appropriate matching network to match the resistance for maximum power transfer or reliable operation of the system.

Describing your system, selection of transistors, design equations and calculations, simulation results (Gain plot, input signal, output signal) from the SPICE simulator, and finally discussion and conclusion.

Reference no: EM131433812

Questions Cloud

Before rule promulgated by federal agency becomes law : Before a rule promulgated by a federal agency becomes law, it must be. The court's standard of review will give the greatest deference to any agency's decision when the plaintiff.
Provide examples of ordinary versus extraordinary means : Provide examples of ordinary versus extraordinary means used in the treatment of the terminally ill. In your opinion, which example provides the most meaningful care for these patients? Why did you answer this way? Provide examples and references ..
Aggregate expenditure and aggregate demand curves : (a) Compare and contrast the Aggregate Expenditure and the Aggregate Demand curves. (Hint: include aspects such as; definition, underlying assumptions, derivation, slope, shift factors).
Whats at stake for the key parties : Whats at stake for the key parties, including those with whom Susan disagrees and what are the main arguments Susan is trying to counter? That is, what are the reasons and rationalizations you need to address?
Design an audio amplifier system : Question: Design an audio amplifier system that will take input signal of 100 mV from a microphone of 75 ?, amplify the signal with a gain of 40, and finally drive a speaker of 8 ?
Opening cuba to international travel affect travel industry : How will opening Cuba to international travel affect the travel industry in the United States and other countries? What are the potential benefits of virtually open travel to Cuba to Buban citizens as well as the Cuban government?
What is the real interest rate that taylor paid : Jordan loaned Taylor $1,200 on March 15, 2009. Taylor returned $1,260 on March 14, 2010. Inflation was 2% over the 1-year period. What is the real interest rate that Taylor paid?
Which web server has proven most popular : Which web server has proven most popular since the dawn of the web? Describe what it means to scale web services vertically and horizontally. Explain why you might choose each depending on your environment and requirements.
Shift to the right of the demand curve : In terms of the supply and demand analysis this is explained by a shift to the right of the demand curve.

Reviews

Write a Review

Other Engineering Questions & Answers

  Draw a block diagram for the subtracter-comparator

Design a binary divider which divides a 7-bit dividend by a 2-bit divisor to give a 5-bit quotient. The system has an input St that starts the division process. Draw a block diagram for the subtracter-comparator. You may use fulil adders or full..

  Design a synthesizable convergent rounder

The convergent rounder in this lab rounds the number based on fractional part of the number. The following is the criteria that you need to consider when designing this rounder:

  Differential balance on co2 in the liquid phase

Write a differential balance on CO2 in the liquid phase and integrate it to derive the relation CA (t) = C*A [1 - exp (- kSt/V)] where S (cm2) is the effective contact area between the gas and liquid phases.

  Determine the strength ratio r at the bottom surface

Determine the strength ratio R at the bottom surface of the laminate, using theMaximum stress, and Maximum strain strength criteria:

  Calculate the characteristic impedance

Microwave Systems Design Tech - Assignment. Give a brief definition of the term characteristic impedance and what is it measured in? Calculate the characteristic impedance using the following information. The capacitance and inductance per unit lengt..

  What is the cutoff frequency you measured from simulation

What is the cutoff frequency you measured from the simulation? Based on the cut off frequency, what type of active filter is constructed in this lab?

  Disc profiles in order to get job

Part 1: Write a brief essay describing two ways you would effectively use the DiSC profiles in order to get job.

  1a company is confronting an energy efficiency problem in

1. a company is confronting an energy efficiency problem in which they are experiencing a quite high loss of

  Demonstrate knowledge of it structures

Radio Frequency Identification Tags (RFIDs) are being used in ever greater numbers for an increasing diverse number of applications, from libraries to retail shops to Oyster cards.

  Find the stationary probability measure

What is the state space S of this process - Find the stationary probability measure Π of this process for general M - Define the time-dependent mean size of the population by µ1(t) = Σn=0M npn(t). Show that µ1(t) = Me-γt.

  How long after the arrival of the first vehicle will it take

If uniform deterministic processing of vehicles (collecting of fees) begins 20 minutes after the first arrival and the total delay is 3200 veh-min, how long after the arrival of the first vehicle will it take for the queue to be cleared?

  Calculate the average dry and web bulb temperatures

Calculate the average dry and web bulb temperatures and find the relative humidity using the Psychometric chart and submit with your assignment

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd