Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
You are given the following components: MOS (p and n) npn and pnp transistors with parameters given in the text or select your own by using industrial data sheets, available on the internet. Also resistors, capacitors, and power supplies (10 V, 5 V, and 3.3 V) are available. Design one of the following amplifiers:1. Voltage gain of 40 dB, input resistance 50 KW or more, and load resistance of 20 KW.2. Voltage gain of 25 dB, input resistance 2 MW or more.3. Voltage gain of about 0 dB, input resistance 10 MW or more, and load resistance of 20 KW.4. Current gain of about 0 dB, input resistance 50 W or more, and load resistance of 1 KW.5. Voltage gain of about 0 dB, input resistance 1 KW or more, and load resistance of 50 W.
A capacitor in an RC circuit with R = 5.00 ohm and C = 6.00 mF is being charged. What is the time required for the capacitor voltage to reach 86.5 percent of its steady-state value
draw the sympol and truth table of the gate that corresponds to the action of the logic gate.
an electric motor has an armture constant of 140, a flux of 25 mwh, an armuture current of 30 A , and a rotatio?nal speed of 1600 rpm. what is most nearly the power output in watt
encounter a sequence of birds while walking in the park. The birds can either be blue (B) or red (R). We let X be the random variable corresponding to the number of birds we encounter until seeing the first blue one.
(a) Design a simple PNP current source to give an output current of IO = 0.5 mA (nominal value). The transistor parameters are f = 50, VEE = 10 V, VCC = 10V, |VBE| = 0.7 V, |VCEsat| = 0.3 V and VA = 50 V (for all transistors)
A saturated npn transistor has a base to emitter applied voltage of 0.6V. The collector to emitter voltage is 0.2V. The collector current is 12mA
The LM358 op amp can be a single or dual supply op-amp. This mean that it can operate with just a single supply i.e. + 5 volt or with dual supplies i.e. (+ and -) 5 volt supplies. With a inverting configuration with dual supplies (+5v and -5v) bei..
When the two windings are connected to a a.c supply of 50hz, the field current is 0.1A, the armature current is 100A and the phase difference between them is 60 degree. calculate the average torque and maximum torque.
Analog to Digital Converters The input signals of an (10bits) ADC are from -1Volt to +1Volt. a) What is the rage of the converters b) What is the resolution c) What is the precision What is the value the minimal input signal variation that this ADC c..
A linear-phase FIR filter should be designed with the ideal magnitude response shown in Figure 1 which represents an narrow band-pass filter. The lower cutoff frequency, fL , is 2,000 Hz, and higher cutoff frequency, fH , is 3,600 Hz.
The feedback capacitance of an inverting amplifier is 10pF. What is the Miller capacitance at the input if the gain of the amplifier is -120 What is the Miller capacitance at the output of the amplifier
Bipolar Junction Transistor, A silicon n-p-n bipolar junction transistor is designed with emitter, base and collector doping levels of 10^19cm, 10^15cm and 5*10^17cm, respectively.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd