Design a synchronous tdm carrier to support 30 channels

Assignment Help Electrical Engineering
Reference no: EM13285847

Asssume that you are to design a synchronous TDM carrier to support 30 voice channels using 6-bit samples and structure similar toT1.Determine required bit rate ?

Reference no: EM13285847

Questions Cloud

Community that can be mitigated by source control : What are two hazards in your community that can be mitigated by source control? And, what type of control is used? How effective are these controls?
Compute the resistivity of the wire : A wire has a diameter of 1.74 mm and a length of 37 m, What is the resistivity of the wire?
How much would your payments be each month : If you were going to buy your office from Mrs. Beach for $500,000 with 10% down payment, 15 years financing with a 6% interest rate, how much would your payments be each month?
Evaluate the relative percentages of each product : Chlorination via radical halogenation is a very unselective process and can lead to the formation of all three of the below products. Estimate the relative percentages of each product that will be formed using this means of halogenation. Presume t..
Design a synchronous tdm carrier to support 30 channels : Asssume that you are to design a synchronous TDM carrier to support 30 voice channels using 6-bit samples and structure similar toT1.Determine required bit rate
Saharan slave trade differ from the atlantic slave trade : How did the Atlantic system affect Europe, Africa, and the Americas? Who were Indentured Servants and how were they different from African slaves? How and why did the West Indies and other places in the Americas become centers of African population a..
Compute the beat frequency : Two pure tones are sounded together. The periods of their pressure variations are 0.0151 s and 0.0159 s, What is the beat frequency
Design a device which will input two 4-bit unsigned numbers : Design a device which will input two 4-bit unsigned numbers and subtract twice the smaller of the two numbers from the larger of the two numbers (That is, input x and y and output x - 2y if x > y and output y - 2x otherwise.)
Explain relation in the atomic numbers and the ionic radius : What is the relationship between the atomic numbers and the ionic radius of the elements in a group.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the vector part of e1 normal to the interface

If one of the normal vectors to an interface is n-hat = 1/sqrt(13) (3x-hat + 2z-hat) and the electric field just below the interface is E1 = 9x-hat + 2y-hat + 2z-hat, what is the vector part of E1 normal to the interface

  Find the attenuation factor of fog of electromagnetic wave

A laser beam traveling through fog was obseved to have an intensity of 1w/m^2 at a distance of 2 meters and intensity of 0.2 w/m^2 at a distance of 3 meters. Knowing that the intensity of an Electromagnetic wave is proportionel to the square of it..

  Find the phase voltage and phase current at the load

The transformer input is a three wire three phase 120V (line-to-line) system. the transformer output supplies a "Y" connected three phase load with a phase impedance of 600 + j300 ohms. A. sketch the diagram of the system described above.

  What is the average current drawn from the power supply

a) It is required that the propagation delay be limited to 60 psec. Find the required device widths b) Find the High and Low noise margins, i.e. NMH and NML. c) What is the peak current drawn from VDD during switching of the inverter What is the aver..

  What is the approximatereal power at the power factor

In a certain balanced three-phase system, each line current is 5A and each line voltage is 220 V. What is the approximatereal power, if the power factor is 0.7

  Find power factor and state whether it is lagging or leading

The phasor voltage across a certain load is V = 1200√2

  Identify the modes and all cut off and resonant frequencies

Make a plot of group velocity versus frequency for frequencies from 0 Hz to 500 kHz. Your plot should have 3 different curves for the three modes of propagation. Be sure to identify the modes and all cutoff and resonant frequencies clearly.

  Determine max temperature in the rod and the heat flow rate

Two large plates at temperatures of 90C and 70C are separated by a steel rod .3m long and 0.025m in diameter. The rod is welded to each plate. The space between the plates is filled with insulation that also insulates the circumference of the rod.

  Explain choice in terms of current offset at summing point

In order to control the slope of a ramp produced by an integrator, the values of Vin, R, and C may be varied. Assuming a fixed value for C of 10 μF, would it be better to have a relative large Vin with a correspondingly large value of R

  Write a program sequence that places the value in address

Write a program sequence that places the value in Address $1500 into Accumulator A. Then, AND this value with the value in Address $1501. Save the result in $1502.

  If the string is vibrating in fifth harmonic how long is it

The wave function of a certain standing wave on a string fixed at both ends is y(x,t) = 0.30 sin(0.0025x)cos(300t) where y and x are in centimetres and t is in seconds. If the string is vibrating in its fifth harmonic, how long is it

  Compute the line losses and voltage across the load

A simple power system consists of a dc generator connected to a load center via a transmission line. The load resistance is 8 ohms. The transmission line is 40km copper wire of 4 cm diameter. If the voltage at the load side is 400 V, compute Volta..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd