Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Design a device which will input two 4-bit unsigned numbers and subtract twice the smaller of the two numbers from the larger of the two numbers (That is, input x and y and output x - 2y if x > y and output y - 2x otherwise.) Use the following devices we've studied (n-bit adder/subtractor, n-bit comparator and MUXes as well as combinational gates in your design.
Perform experiments using your circuit design. Using your digital scope, plot (and submit) input voltage and output voltage from your circuit design. Try to vary the filter portion (R, L, C) of your circuit and plot (and submit) output voltages.
Design an open-circuited, shunt stub matching network to match a 125 + j20 ohm load to a 700 MHz, 50 ohm generator. Show the lengths of your transmission lines in fractions of a wavelength. Show steps to solution please.
Design a DC power supply that provides -95v +/- 5v to a 2 amp load (energy absorber). The input source is a 100 volt peak sinusoid, 60 Hz. You may use any basic circuit element. State the values of all circuit elements (in ohms, farads, etc).
An NMOS device has parameters V_TN=0.8V, L=0.8µm, and k_n^'=120µA/V^2. When the transistors is biased in the saturation region with V_GS=1.4V, the drain current is I_D=0.6mA. A) What is the channel width W
A transducer produces a sinusoidal waveform with an amplitude of 2.5 VPK and a DC offset of 0 VDC. The ADC input signal range is 0 V to 5 V. Describe the signal conditioning circuit that is needed to use the full-scale range of the ADC.
A true centrifugal casting operation is to be performed in a horizontal configuration to make cast iron pipe sections. The sections will have a length = 42.0 in, outside diameter = 8.0 in, and a wall thickness = .50 in
1- Find F(s) for = A[ a cos(ßt) + b sin(ßt)] u(t) and plot and the poles and zeros in the S- plane. 2- find f(s) for = 2d(t) +4e^-2t cos(2t) u(t) and plot and the poles and zeros in the S- plane. 3- find f(s) for = 10[3-6t-4e^-2t] u(t) and plot and t..
assuming positive-sequence operation,calculate the exact abcd parameters of the line.compare the exact B parameter with that of the nominal II circuit.also compare the equivalent and nominal II circuit for the line.
Presuming that oscillations in wavefunction amplitude lead to oscillations at the same frequency in the charge density, and that the charge density at any point in the structure give rise to radiated electromagnetic radiation at the same frequency
The temperature of steam at the inlets of both turbines is 500°C, and the enthalpy of steam is 3185 kJ/kg at the exit of the high-pressure turbine, and 2247 kJ/kg at the exit of the low-pressure turbine. Disregarding the pump work, determine the w..
Compute the complex power S (in polar form) drawn by a certain load if it is known that (a) it draws 100 Waverage power at a lagging PF of 0.75; (b) it draws a current I = 9 + j5 A rms when connected to the voltage 120/32 V rms
You are asked by your supervisor to witness factory tests to be performed on 15 single-phase transformers that your company plans to purchase. The 15 single-phase transformers will be used to make five three-phase banks.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd