Design a retrofit undamped absorber

Assignment Help Mechanical Engineering
Reference no: EM131143964

A small rotating machine weighing 50 lb runs at a constant speed of 6000 rpm. The machine was installed in a building, and it was discovered that the system was operating at resonance.

Design a retrofit undamped absorber such that the nearest resonance is at least 20% away from the driving frequency.

Reference no: EM131143964

Questions Cloud

What is the wavelength of the standing wave pattern : The speed of waves along the string increases with increasing tension in the string. Should the magnitude of M be increased or decreased in order to double the number of antinodes in the standing wave pattern. Justify your answer.
Calculate the damping ratio required : Calculate the damping ratio required to limit the displacement transmissibility to 4 at resonance for any damped isolation system.
Determine the radius of curvature r : A W200 X 31.3 rolled-steel beam is subjected to a couple M of moment 45 kN.m. Knowing that E = 200 GPa and n = 0.29, determine
Determine the largest couple m that can be applied to a beam : (a) Using an allowable stress of 120 MPa, determine the largest couple M that can be applied to a beam of the cross section shown. (b) Solve part a, assuming that the cross section of the beam is an 80-mm square
Design a retrofit undamped absorber : Design a retrofit undamped absorber such that the nearest resonance is at least 20% away from the driving frequency.
Calculate the range of frequencies : Calculate the range of frequencies at which the amplitude of the machine vibration is less with the absorber fitted than without the absorber.
Rendering the system safe for operation : Redesign the absorber so that ω1 6 2000 rpm and ω2 7 4000 rpm, rendering the system safe for operation.
Calculate how much spoils the absorber design : Calculate how much spoils the absorber design by determining the magnitude X using equation (5.32).
Prepare a recommendation : prepare a recommendation. - In recommendation, you will want to have a table showing the payback period, accounting rate of return, net present value, and internal rate of return for each proposal.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Rotational inertia of the shell about that axis

A thin spherica lshel'I has a radius of 1.90 m. An applied torque of 960 N.m gives the shell an angular acceleration of 6.20 rad/s2 about an axis through the center of the shell. What is rotational inertia of the shell about that axis?

  Determine the maximum speed at which vehicle can travel

Determine the maximum speed at which the vehicle can travel round a curve of radius 90 m and the angle to which the curve would have to be banked for the vehicle to travel round it at a speed of 60 km h 1 without any tendency to side-slip?

  Air at 15 degc and atmospheric pressure is forced over the

water at the rate of 0.8 kgs at 93 degc is forced through a 5 cm id copper tube at a suitable velocity. the wall

  Expression for the rate of heat loss to surrounding fluid

A spine attached to a wall maintained at a uniform temperature Tb has the shape of a circular cone with base diameter b, height L and a concave parabolic profile, and it is exposed to a fluid at a uniform temperature T?.

  Air is at 70degc and 97 kpa at the beginning of the

a four-cylinder two-stroke 2.0-l diesel engine that operates on an ideal diesel cycle has a compression ratio of 22 and

  Determine the steam quality at the turbine exit

For T 5 808F, determine the steam quality at the turbine exit, the steam mass flow rate, in lb/h, and the thermal efficiency. Plot the quantities of part (a) versus T ranging from 80 to 1058F.

  Determine the net power developed per unit mass

(a) determine the net power developed per unit mass flowing, in kJ/kg, and the thermal efficiency for a compressor pressure ratio of 8. (b) plot the net power developed per unit mass flowing, in kJ/kg, and the thermal efficiency, each versus compr..

  Temperature of the atmosphere varies with height

Using the hydrostatic law dp/dz = -(rho)g and the ideal gas law p = (rho)RT, show that if the temperature of the atmosphere varies with height as T(z) = T_o - Bz, then the atmospheric pressure varies with height as p(z) = p_o(1-(Bz/T_o))^(g/(BR))

  Predict ratio of average graphite ?ake

Class 20 and class 60 gray cast irons have tensile strengths of about 20 and 60 ksi respectively. Assuming that the fractures start from graphite ?akes and that the ?akes act as preexisting cracks, use the concepts of Grif?th analysis to predict t..

  Projection welding

Name products that are manufactured using these processes and write two sentences on why you know it's made from this process.

  Determine the amount of carbon monoxide formed in lbm and

12 lbm of carbon c reacts with 24 lbm of oxygen o2 to form 22 lbm of carbon dioxide co2 plus an unknown amount of

  Determine the initial volume of the cylinder

A mass of 0.5 g of air is contained in a piston-cylinder device. Initially the system is at 100 kPa and 25°C. The system is now compressed adiabatically to a volume 17 times smaller and a temperature of 700 K.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd