Design a passive low-filter using resistors and a capacitor

Assignment Help Electrical Engineering
Reference no: EM13289989

Design a passive low-filter using resistors and a 100uF capacitor that will have a passband gain of 0.8 and a cutoff frequency of10000 HZ.

Reference no: EM13289989

Questions Cloud

What are the two possible resistances of the light bulb : A light bulb is wired in series with a 133-? resistor, and they are connected across a 120-V source. What are the two possible resistances of the light bulb
Enter a decimal value : Enter a decimal value
What must the voltage applied at the armature terminal be : A permanent magnet commutator motor produces a torque of8 N. m with armature current = 10A. armature R=.16 ohms. if motordrives a load requiring torque of 20 N. m at speed = 1800rpm
Find the fractions of the cube immersed in water and oil : A large container, open at the top, is half-filled with water (?H2O = 1000 kg/m3). Determine the fractions of the cube immersed in water and oil
Design a passive low-filter using resistors and a capacitor : Design a passive low-filter using resistors and a 100uF capacitor that will have a passband gain of 0.8 and a cutoff frequency of10000 HZ.
Find the components of the displacement vector : Suppose the superhero had flown 145 m at a 125° angle with respect to the positive x-axis
Find must be the length of the wire : A 115-V source of emf is attached to a heating element with is a coil of nichrome wire (r=100*10^-8) of cross section 1.20 mm^2. What must be the length of the wire
How to simplify and express the function in sao form : if input variables have more 1's than 0's, a majority function isgenerated in combinational logic circuits with an output equal to1. otherwise the output is equal to 0.design three input majority functions following the steps and conditions given ..
What is the force that acts on the electron : A long straight wire carries a current of 4.5 A. The wire is horizontal in the plane of the page (screen), What is the force that acts on the electron

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find when the triggering angle is greater than 140 degrees

The average voltage across the load when the triggering angle is 140 degrees. Keep in mind that the conduction is incomplete when the triggering angle is greater than 140 degrees.

  Find and characterize the location of images of the film

The film is developed with an overall gamma of 2, reinserted in the position of the film during recording and reconstructed using the same point source as that used to construct the hologram. Using laws of ray tracing of the hologram, find and cha..

  Draw a state transition diagram for the state machine

The value of Q is 1 if and only if the number of 1's in the sequence of input P is not divisible by 2 and not divisible by 3. Otherwise, the output value Q is 0. Draw a state transition diagram for the state machine using as few states as possible..

  Determine the left triceps muscle force

Determine the left triceps muscle force (Ftri), elbow joint reaction force (Rj) required to hold this position along with any ground reaction forces (Rg) and/or reaction moments (Mg) in the hand. Show all necessary free body diagrams along with th..

  How to write an expression for the forced response

The low pass filter G(s)= (s+5)/(s+10) is given. Derive the forced response y1(t) for x1(t)=10exp(-0.1t). Write an expression for the forced response y2(t) when the input is x2(t)=12exp(-0.1t)cos(2t).

  What is effective radiated power of television broadcast

What is the effective radiated power of a television broadcast station if the output of the transmitter is 1000 W, antenna transmission line loss is 50 W, and the antenna power gain is 3

  Find the leakage current through a polyester capacitor

A Polyester capacitor with a leakage specification of 5x109 O -µ F is used in a circuit. The voltage across this capacitor is 100 volts D.C. and the capacitance is 0.1µ F find the leakage current.

  Determine the steady-state error for a unit step input

For a unity feedback control system, the forward path transfer function is: G(s) = 20/(s^2 + 14s +50) a. Determine the steady-state error for a unit step input. b. Find the steady-state error for a unit ramp input using the Final Value Theorem.

  Design an embedded system to turn on an led

Design an embedded system to turn on an LED when it is dark and turn off of LED during the day time.

  Determine the uncorrected poer factor and reactive load

A 2.4KV, single-phase circuit suppllies a load of 250KW at a lagging power factor, and the load current is 160A. If it is necessary to improve the power factor, determine the following: (a)The uncorrected poer factor and reactive load.

  Write an assembly-language program to add

Write an assembly-language program to add $40 to each element of list1 and store it to the corresponding element of list2. Use a loop. ORG $2000 LIST1 DC.W $21, $442, 3, 4, 5

  How much energy is used by the resistor in 5 min

A 26 resistor is connected across a 65 V battery. How much energy is used by the resistor in 5 min

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd