Design a logic network to control the lights of the doors

Assignment Help Electrical Engineering
Reference no: EM13294994

A long hallway has three doors, one at each end and one in the middle. A switch is located at each door to operate theincandescent lights along the hallway. Label the switches A,B, and C. Design a logic network to control the lights.

Reference no: EM13294994

Questions Cloud

Design half-wave rectifier power supply to deliver avg volt : Design a half-wave rectifier power supply to deliver an average voltage of 9V with a peak to peak ripple of 2V to a load. The average load current is 100mA. Assume that ideal diodes and 60Hz. ac voltage sources of any amplitudes needed are avail..
How to determine delta h for the reaction : Using only your answer to a, and the following information: Delta H = -283.0 kJ/mol for the reaction: CO(g) +1/2 O2 (g) --> CO2 (g), determine delta H for the reaction: 4CO (g) + 2NO2 (g) --> 4CO2(g) + N2 (g).
What is the skateboards acceleration down the ramp : a skateboard with mass M rolls down a ramp, starting from rest. It takes a time T to roll a distance L along the ramp
Determine the heat transferred per pound mass : For the process where wk(closedsystem)=778 ft*lbf/lbm and ?u= 0.75 Btu/lbm, determine the heat transferred per pound mass
Design a logic network to control the lights of the doors : A long hallway has three doors, one at each end and one in the middle. A switch is located at each door to operate the incandescent lights along the hallway. Label the switches A,B, and C. Design a logic network to control the lights.
Estimate the mass of the ball : A bat hits a moving baseball. If the bat delivers a net eastward impulse of 1.5 N-s, what is the mass of the ball
Explain what is the effect does using 1 degree and 2 degree : In nucleophilic substitution reactions, what is the effect does using 1 degree, 2 degree, and 3 degree substrates have
What is the current in the block : A 5.78 cm long rod in the shape of a rectangular solid has cross section dimensions 28.7 mm x 42.6 mm. What is the current in the block
Determine peak current and peak inverse voltage for diode : A 20-V-rms 60 Hz ac source isin series with an ideal diode and a 100 ohm resistance. Determine the peak current and peak inverse voltage(PIV) for the diode.

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  Describe what happens when listen is invoked for tcp socket

List three standard socket calls that you would expect every connection-oriented server to invoke that would not normally be invoked by any client. Briefly indicate why a typical client would not need to invoke these calls.

  How to connect both circuits to a 25k ohm load resistor

a. Given a circuit with a VCVS (A=1000) in series with a 100K ohm resistor, convert this circuit to a VCCS  in parallel with a resistor R. b. Connect both circuits to a 25K ohm load resistor and show they produce the same behavior in the load resis..

  Find the ratio of the two capacitances of circular capacitor

A circular capacitor of radius r is made using SiO2 as the dielectric on a silicon wafer. If a trench of depth l is made to replace the circular capacitor with the trench capacitor with trench depth l, find the ratio of the two capacitances.

  Find the z-transform of functions by bringing into a form

Find the inverse z-transform, x(n), of the following functions by bringing them into a form such that you can look up the inverse z-transform from the tables. This will require some algebraic and /or trigonometric manipulation/calculation.

  Calculate and show amplitudes of all rising and falling edge

Transmission line A coaxial transmission line has characteristic impedance Z0 = 50 ohms and has length L = 200 m and phase velocity vp = 2.0e8 m/s. The end at x = 0 is terminated with Rs = 50 ohms and the end at x = L is terminated with RL = 75 oh..

  Obtain coefficients of digtal filter that is maximally flat

obtain, via the bilinear transform, the coefficients of a digtal filter that is maximally flat in the passband, 0 to 4 kHz, and has an attenuation of at least 25 dB at frequencies over 10 kHz. Assume a sampling frequency of 32 kHz.

  Determine the number of resistors and current in each branch

A certain parallel resistor circuit consists of only ½ W resistors. The total resistance is 1.0 k-ohm, and the total current is 50 mA. If each resistor is operating at one-half its maximum power level

  Describe how an ideal inductor reacts to steady state dc

Describe how an ideal inductor reacts to steady state DC and why. State the equation for finding the instanteneous current in an inductor during the transient period. Explain each part

  Find q1 such that the force on a test charge given

Point charges Q1 and Q2 are respectively located at (4,0,-3) and (2,0,1). If Q2 = 4 nC, find Q1 such that (a) The E at (5,0,6) has no z-component (b) The force on a test charge at (5,0,6) has no x-component.

  Explain what is the db bandwidth of the amplifier

A 1 kHz sine wave signal with a power level -10 dBm is applied to the input of the amplifier. What is the power at the amplifier output in dBW?

  Determine what is the highest possible operating mode

A rectangular waveguide with dimensions a=2b=5cm operates at11 GHz. Assuming that the guide is filled with air, find the highest possible operating mode and the intrinsic wave impedance at that mode.

  What is depth of junction assuming p side is uniformly doped

A silicon diode has a doping profile such that ND = ax3. What is the depth of the junction assuming the p side is uniformly doped with NA per cubic cm. Assume the x origin is at an ideal ohmic contact on the n side of the diode.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd