User Account

All Pages

Derive an expression for the power loss

Assignment Help Electrical Engineering
Reference no: EM131199566

1. A 250 m, 2 wire D.C. distributor fed from one end is located uniformly at the rate of 1.6 A/metre. The resistance of each conductor is 0.0002 ohms per metre. Find the voltage necessary at feed point to maintain 250 V

i) At the far end
ii) At, the mid-point of the distributor

2) Derive an expression for the power loss in a uniformly loaded distributor fed at one end.

Reference no: EM131199566

Questions Cloud

How current changes in federal and local policies influence : How might current changes in federal, state, and local policies influence decisions to be made? Include a schedule of assumptions for your proposal. What questions might the board ask regarding feasibility of this proposal?
Pursuing a job opportunity : What tools/methods do you anticipate using in your job search following your graduation? Have you run into remarkably good or bad experiences you'd like to share? (If so, keep thing anonymous!) How prepared would you feel in pursuing a job oppo..
Which is a part of the process of redesigning work : Which of the following is best classified as a polycentric policy of strategic approaches to international staffing? Which of the following is a part of the process of redesigning work?
Creating outline for speech after watching outline lesson : What have you learned about creating an outline for your speech after watching the outline lesson? Discuss the importance of identifying general purpose, specific purpose, central idea, and organization of your main points. Do not just provide defini..
Derive an expression for the power loss : Find the voltage necessary at feed point to maintain 250 V At the far end, -At, the mid-point of the distributor. -Derive an expression for the power loss in a uniformly loaded distributor fed at one end.
Explain the significance of the selected category : Describe the selected content and explain the significance of the selected category across all of the religions studied. Show in what ways the category is significant for each religion.
Vision statements are living documents : Vision statements are "living documents", meaning that you can change them based on change in circumstance, share your clearly thought out and critically reflective vision statement. It can not be less than 50 words in length and should clearly conve..
Identify strategies you feel that best address the challenge : Describe at least 2 challenges that supply chains face in each of these areas. Identify the strategies you feel that best address those challenges, and explain why.
Richard is getting free board and lodging - advise richard : HI6027: BUSINESS AND CORPORATIONS LAW - During the first year of the agreement, Joe entered into a contract to star in a film being made by Pretty Pictures. Does Frère Bros have any remedy?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the maimum voltage that can be put across a 1 watt

The power in watss disspiated by a resistor is given by P=IV. The resistors used are 1 watt resistances i.e. they are capable of dissipating a maximum of 1 watt without overheating. What is the maimum voltage that can be put across a 1 watt, ..

  Calculate the total complex power

Calculate the total complex power, total current drawn and the total power factor and Y-connected load with an impedance of (1+ j 6) ohm per phase,

  Calculate position of the object if distance is given

A microscope has a 2.70-cm focal length eyepiece and a 0.630-cm objective lens. For a relaxed normal eye (assume a viewing distance of 25.0 cm), calculate the position of the object if the distance between the lenses is 13.5 cm

  Create a plot of the measured snr (db)

For comparisons, plot the original speech and the quantized one using 3 bits, 8 bits, and 15 bits.

  What is the period of the oscillation

A 2.0 kg particle moves along the x axis. Its position varies with time according to x = t + 3.0t^3, Where x is in meters and t is in seconds. (a) Find the work done on the particlein the interval t = 0 to t = 1.70s.

  Determine at what value of r3 will the bridge null

A sensor with a nominal resistance of 50 ? is used in a bridge with R1 = R2 = 100 ?, V = 10.0 V, and R3 = 100  potentiometer. It is necessary to resolve 0.1  changes of the sensor resistance. A) At what value of R3 will the bridge null

  How large is the correlation coefficient for gsm 900 system

Assuming that directions of arrival are uniformly distributed at the mobile, how large is the correlation coefficient for a GSM 900 system between the channel in the middle and the end of the burst when the mobile station moves at 200 km/h

  How long does it take light from sun to reach neptune

The average orbital radius of Neptune is 2.8 billion miles. Given that distance, how long on average does it take light from the sun to reach the planet Neptune in hours (Speed of light in English system = 186,282.4 miles/second)

  What would be the current drawn by two such bulbs

Consider the problem of using a low-voltage system to power a small cabin. Suppose a 12-V system powers a pair of 100-W lightbulbs (wired in parallel). a. What would be the (filament) resistance of a bulb designed to use 100 W when it receives 12 V

  What is the satellites transmitter output power required

Given a LEO satellite system with a dish gain of 20 dB , orbiting altitude of 789 km, and download frequency of 1626 MHz , what is the satellite's transmitter output power required so that it is received by a wireless phone with 1 pW

  Describe the oscillations in electric circuits

The following functions describe the oscillations in electric circuits and the vibrations of machines and structures. Plot these functions on the same plot. Because they are similar decide how best to plot and label them to avoid confusion.

  Calculate the slip of load with the mechanical losses

An induction motor has an efficiency of 0.80 when the load is 50 h.p. At this load , both stator copper loss and rotor copper loss are equal to the core losses . The mechanical losses are one -fourth of the no load losses . Calculate the slip.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd