Define what is the specific heat of the metal

Assignment Help Chemistry
Reference no: EM13551397

A 125g piece of metal is heated to 288c and dropped into 85.0g of water at 26.0c. If the final temperature of the water and metal is 58.0c then what is the specific heat of the metal.

Reference no: EM13551397

Questions Cloud

Define activated carbon during a recrystallization : What is the reason for using activated carbon during a recrystallization. Why is gravity filtration and not suction filtration used to remove insoluble suspended impurities and charcoal from a hot solution
Describe the path of the electron while in magnetic field : A electron enters a magnetic field of 0.3 T at an angle of 35 degree and with a speed of 5.00 E5 m/s. Find the force on the electron. Describe the path of the electron while in the magnetic field.
What is the maximum net loss : 1. A trader creates a long butterfly spread from options with strike prices $60, $65, and $70 by trading a total of 400 options. The options are worth $11, $14, and $18. What is the maximum net loss (after the cost of the options is taken into ..
Find what is the mass of the aluminum cup : An aluminum cup contains 225 g of water and a 40 g copper stirrer, all at 27°C. Calculate the mass of the aluminum cup
Define what is the specific heat of the metal : A 125g piece of metal is heated to 288c and dropped into 85.0g of water at 26.0c. If the final temperature of the water and metal is 58.0c then what is the specific heat of the metal.
What is the voltage of the alternator : A series RCL circuit includes a resistance of 298 ohm, an inductive reactance of 648 ohm, and a capacitive reactance of 415 ohm. The current in the circuit is 0.634 Amps. What is the Voltage of the alternator?
Find current that is sum of currents through each resistor : A 9 volt battery is connected in parallel with a 100 ohm, 200 ohm, and 500 ohm resistors. Find the total resistance in order to find the current that is the sum of the currents through each resistor. How much current flows through each resistor?
What is the engines efficiency : With each cycle, a 2510-W engine extracts 2070 J from a thermal reservoir at 90 °C and expels 1340 J into a thermal reservoir at 20 °C. What is the work done for each cycle? What is the engine's efficiency?
How far from home plate would the ball land if not caught : A batter hits a fly ball which leaves the bat 0.88above the ground at an angle of 62 with an initial speed of 28 heading toward centerfield. Ignore air resistance. How far from home plate would the ball land if not caught? T

Reviews

Write a Review

Chemistry Questions & Answers

  Explain during the bromination of trans-cinnamic acid

How might you use 13C NMR spectroscopy to determine if the brominated product is contaminated with some unreacted starting material (during the bromination of trans-cinnamic acid)

  What is the pressure of iodoethane after three half-lives

If the initial pressure of iodoethane is 894 torr at 245°C, what is the pressure of iodoethane after three half-lives?

  What is the pressure of the gas

A manometer shows a mercury level of 225 mm Hg on the closed end of the tube and 108 mm Hg on the open end. If the atmospheric pressure is 760 torr,

  Use the atomic mass of indium to calculate

Indium has only two naturally occurring isotopes. The mass of indium-113 is 112.9041 and the mass of indium-115 is 114.9039 .

  Evaluate the normalization constant for the eigenstates

Find the energy eigenstates for the system. Compute the normalization constant for these eigenstates. What is the boundary condition for this problem. What does this restrict the allowed energies of the system to be? e) What is the degeneracy of t..

  Define the general physics of chromatography

Explain the general physics of chromatography. Illustrate these general principles with regard to paper, thin layer, gas, liquid, and super-critical fluid column and open tube chromatography.

  Explain and identify the property of gas that is measured

Identify the property of gas that is measured in each of the following: a) 425 K; b) 1.0 atm; c) 10.0 L; d) 0.50 mol of He.

  Explain the melting behavior expected

The melting point of a pure compound is known to be 110-111°. Describe the melting behavior expected if this compound is contaminated with 5% of an impurity.

  Explain molarity of naoh is too high or low

A student failed to carry out all of the procedural steps when doing this experiment. Would the following procedural variations result in an experimentally determined molarity of NaOH that is too high or low? Briefly Explain. The student did not c..

  What is the capacity factor for the analyte

Consider a chromatogram containing a single analyte with retention time of 4 minutes. The mobile phase elution time is 0.2 minutes. What is the capacity factor (k') for the analyte in question?

  State what maximum mass of carbon dioxide is produced

What maximum mass of carbon dioxide is produced by the complete combustion of 10.0 kg of this fuel?

  Define how to calculate the final temperature

Assuming the final mixture has a specific heat capacity of 4.18 J/g*degrees celsius, calculate the final temperature. The enthalpy of fusion for ice is 6.02 KJ/mol.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd