Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A town is considering building a new water treatment facility to treat 32 mgd of river water. The plant will be designed with a rapid mix unit followed by flocculation and sedimentation basin. The water source has an average winter water temperature of 40 and an average summer water temperature of 70oF. The facility will be using alum at dose of 14 mg/L and there is sufficient alkalinity present to ensure there is not a significant pH change during coagulation. It has been identified that charge neutralization is the dominant mechanism for coagulation. The plant manager would like to make sure that there is sufficient.storage on-site for a 2-3 week supply of the concentrated alum solution. it will be up to you to decide how many units you would like to use and the dimensions of each. At a minimum, you need to specify the physical dimensions and layout for this portion of the facility (rapid mix, flocculation, sedimentation), identify specifications for required equipment (you do not need to select a specific motor but you should describe the minimum requirements), and specify required chemicals (i.e., storage and daily use).
The aluminum bar has an electrical coil imbedded in it, so that known amounts of heat can be transferred to it. Aluminum has a specific gravity of 2.70 and a specific internal energy given by the formulaU (kJ/kg)=0.94T(C).
Three streams of polluted air are combined prior to treatment in an electrostatic precipitator (ESP). The flow and particulate concentration of each stream are 600 cfm at150 mg/m^3, 700 cfm at 200 mg/m^3, and 500 cfm at 1000 mg/m^3.
The number of hours on each machine required to produce a product is given in the following table, along with the number of hours available per week on each type of machine. Assume that the company can sell everything it produces.
Water flows i a 8-m-wide rectangular channel that has longitudinal slope of .0001. The channel has an equivalent sand roughness of 2mm. Calculate the uniform flow depth in the channel when the flow rate is 15m^3/s. Use the Darcey-Weisbach equation..
The rapid sand filter being designed for Laramie has the characteristics show below. Determine the head loss for the clean filter bed in a stratified condition. Depth = 0.75 m
what is the maximum load that may be applied to a specimen with a cross sectional area of 130 mm^2 without plastic deformation.
A train moving at 100 km/hr decreases its speed to 80 km/hr in 3.5 seconds. How far, in meters, did the train travel during this time
The aluminum end and the copper end are maintained at temperatures of 50°C and 260°C, respectively. The thermal conductivities of aluminum and copper are 205 and 385 W/m · K, respectively. The temperature of the aluminum-copper junction in the rod..
A 1.50 L buffer solution is 0.250 M in HF and 0.250 M in NaF. Calculate the pH of the solution after the addition of 0.0500 moles of solid NaOH. Assume no volume change upon the addition of base. The Ka for HF is 3.5 x 10-4.
After injecting 50 MMSCF (14.7 psia and 60 oF), the pressure increase from 2500 to 3500 psia. Deviation factors for the gas are 0.90 at 3500 and 0.80 at 2500 psia and the bottom-hole temperature is 160 oF. What is the cubic feet of gas storage spa..
Water in the amount of 1 lb is contained in a rigid closed tank. Initially the water has a quality of 0.4 at a pressure of 10 lbf/in2. Through a stirrer, work is provided to the water in the tank until the pressure quadruples.
Design a lined trapezoidal channel to carry 20 m^3/sec on a longitudinal sloe of 0.0015. The lining of the channel is to be float-finished concrete (n=0.015). Consider (a) the best hydraulic section and (b) the section with side slopes 1.5:1 (H:V)
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd