Crude oil flows through a level section of the alaskan

Assignment Help Mechanical Engineering
Reference no: EM13625879

Crude oil flows through a level section of the Alaskan pipeline at a given rate in millions of barrels per day(1 barrel = 42 gallons). The pipe has an inside diameter of 48 inches; its roughness is equivalent to galvanized iron. The maximum allowable pressure is 1200 psi and the minimum pressure required to keep the dissolved gases in solution in the crude oil is 50 psi. Represent the oil to be equivalent to SAE 30 at 100 C with a density of 910 kg/m^3 and viscosity .01 N *s/m^2. Determine the maximum allowable spacing between the pumping stations as function of the flow rate of oil.

Reference no: EM13625879

Questions Cloud

A pipeline is to be supported above ground on horizontal : a pipeline is to be supported above ground on horizontal beams 14ft long. consider each beam to be simply supported at
Determine the resultant vertical force that the ropes must : when the tucurui dam was constructed in northern brazil the lake that was created covered a large forest. underwater
A block of mass 0222 kg is placed on the end of a spring : a block of mass 0.222 kg is placed on the end of a spring which has a stiffness of 150. nm. it is pulled down 2.60 cm
The magnetic field is 008 tesla and is going into the page : a charged particle has a mass of 20mg and a charge of 0.4 mc. the particle is moving with a speed of 300 ms when it
Crude oil flows through a level section of the alaskan : crude oil flows through a level section of the alaskan pipeline at a given rate in millions of barrels per day1 barrel
Assume the car can be purchased for 0 down for 60 months in : assume the car can be purchased for 0 down for 60 months in lieu of rebate. a car with a sticker price of 42050 with
Determine the fraction of the throttle mass flow that : consider a regenerative rankine cycle with a 600c and 4-mpa throttle a 5-kpa condenser and an open feedwater heater at
A converging lens has a focal length of f 27 cm an object : a converging lens has a focal length of f 27 cm. an object is placed 37 cm from the lens. find the size of the image
Bananas are to be cooled from 24degc to 13degc at a rate of : bananas are to be cooled from 24degc to 13degc at a rate of 215 kgh by a refrigeration system. the power input to the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The gate opens when water levels reaches h2m on the left

water gate is hinged at point o. angle between the gate and the ground is given alpha 60 degrees. the gate opens when

  A tool with a weight of 500lb moves continuously from the

a cantilevered boom is part of an assembly machine. a tool with a weight of 500lb moves continuously from the end of

  Find the rate of change of the density in the tire

Air at 250 kPA and 15C is being forced into a tire, which has a volume of 0.5m^3, at a velocity of 60 m/s through a 6 mm opening. Find the rate of change of the density in the tire.

  The waste heat from the gas turbine is used by an

a gas turbine assume ideal brayton cycle has a pressure ratio of 10. it is connected to an electric generator with an

  An accelerometer mounted inside the train records a

a train enters a curved horizontal section of track at a speed of 100kmh and slows down with constant deceleration to

  Determine the forces in ao, ab, and ac for equilibrium

The lamp has a mass of 15 kg and is supported by a pole AO and cables AB and AC. If the force in the pole acts along its axis, determine the forces in AO, AB, and AC for equilibrium.

  Assuming isentropic efficiencies of 80 percent for both the

a gas refrigeration cycle with a pressure ratio of 3 uses helium as the working fluid. the temperature of teh helium is

  If the environmental temperature is t 40 f what part of

the temperature of 5 lbs of air is raised from 200 f to 500 f at constant pressure with an electrical coil. how much

  The mass flow rate is 556 lbs and the isentropic turbine

water vapor at 800 lbfin.2 1000 degrees f enters a turbine operating at steady state and expands to 2 lbfin.2 the mass

  One structure is made from a si3n4 plate which has a plane

one structure is made from a si3n4 plate which has a plane strain fracture toughness of 3.6 and is alternatively loaded

  Find the volume rate of ?ow in ab

Find the volume rate of ?ow in AB, the velocity in BC, the velocity in CD and the diameter of CE.

  Compute the estimated endurance strength for a

compute the estimated endurance strength for a 20.0mm-diameter rod machined from aisi 5160 oqt 1300 steel and subjected

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd