A pipeline is to be supported above ground on horizontal

Assignment Help Mechanical Engineering
Reference no: EM13625883

A pipeline is to be supported above ground on horizontal beams, 14ft long. Consider each beam to be simply supported at it ends. Each beam carries the combined weight of 50 ft of 48 in diameter pipe and the oil flowing through it about 42000 lb. Assuming the load acts at the center of the beam, specify the required section modulus of the beam to limit the bending stress to 20000 psi. then specify a suitable wide flange of the American Standard beam

Reference no: EM13625883

Questions Cloud

How much power is radiated from each panel assume that the : electronics and inhabitants of the international space station generate a significant amount of thermal energy that the
Determine the max value of p the max stress in the tempered : two tempered steel bars each 316 in thick are bonded to a 12 in mild steel bar. this composite is subjected as shown to
Which statement is true about descriptive : which statement is true about descriptive studies?a descripti e studies are one kind of experimental studyb descriptive
The mases of the three dice are 125 g 143 g and 189 g and : a tabletop gamer has designed a game that requires three dice to be thrown onto a tray with a measurement grid. to add
A pipeline is to be supported above ground on horizontal : a pipeline is to be supported above ground on horizontal beams 14ft long. consider each beam to be simply supported at
Determine the resultant vertical force that the ropes must : when the tucurui dam was constructed in northern brazil the lake that was created covered a large forest. underwater
A block of mass 0222 kg is placed on the end of a spring : a block of mass 0.222 kg is placed on the end of a spring which has a stiffness of 150. nm. it is pulled down 2.60 cm
The magnetic field is 008 tesla and is going into the page : a charged particle has a mass of 20mg and a charge of 0.4 mc. the particle is moving with a speed of 300 ms when it
Crude oil flows through a level section of the alaskan : crude oil flows through a level section of the alaskan pipeline at a given rate in millions of barrels per day1 barrel

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A what is the approximate ductility el of a brass alloy

a what is the approximate ductility el of a brass alloy that has a yield strength of 275 mpa? what is the tensile

  What is the required impeller diameter ratio between the

a 20 mw radial flow hydraulic turbine is to be designed with a head of 70 m and a speed of 90 rpm. a geometrically

  Discuss whether the following situations should be modeled

discuss whether the following situations should be modeled as closed systems or open systems. clearly define the

  Find the rate of waste heat rejection kjhr and the number

a schematic must show th tc qh qc wcycle. always show the hot reservoir at the top amp cold reservoir at the bottom.

  Determine the internal normal force and shear force and the

determine the internal normal force and shear force and the bending moment in the beam at points c and d. assume the

  Draw the stress elements correctly aligned with respect to

1 draw a mohrs circle diagram properly labeled for the following plane stress statesigmax -8 mpasigmay 7 mpatauxy 6

  What is the minimum temperature of the cold reservoir where

a refrigeration system has a coefficient of performance of 5. the heat rejection is an isothermal process at 37c. what

  Calculate assume constant specific heat of cp024 btulbmr

consider an ideal simple gas turbine cycle. for a net power output of 10000 horse power an inlet air temperature of

  What kind of metals are often recommended

What kind of metals are often recommended for use at low temperatures, particularly when any sudden loading of the part is expected?

  The inner and outer surfaces of a 6-m x 7-m brick wall of

the inner and outer surfaces of a 6-m x 7-m brick wall of thickness 41 cm and thermal conductivity .69 wmc are

  Find the actual and carnot thermal efficenciencies of this

a heat engine absorbs 25 mw from a 400 degree c combustion change and rejects 15 mw to the atmosphere at 30 degrees c.

  Compute the maximum bending stress at mid-span

Calculate the maximum bending stress at mid-span, and, for the same section, locate the neutral axis. Neglect the weight of the beam

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd